Industrial Equipment & Supplies
Showing 469–504 of 2702 results
-
Saw BladesBORDO Diamond Saw Blades General Purpose Segmented Rim
- General purpose.
- 7mm segmented rim produces clean, fast cuts wet and dry.
- Great for cutting a wide variety of non-abrasive materials.
- Extreme concentration of diamond for fast, clean cutting and long blade life.
- Can be used for either wet or dry cutting. Extended blade life will be experienced with wet cutting.
- Use when cutting cured concrete, reinforced concrete, clay bricks, hebel®, terracotta tiles, slate, granite, bluestone, fibreglass, reinforced plastics, wall chasing in brick & concrete.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Saw BladesBORDO Diamond Saw Blades Green Concrete and Asphalt
- Green concrete and asphalt blade.
- 8mm segmented rim produces clean, fast cuts wet and dry.
- Segmented blade for abrasive materials.
- Extreme concentration of diamond for fast, clean cutting and long blade life.
- Can be used for either wet or dry cutting. Extended blade life will be experienced with wet cutting.
- Use when cutting asphalt and green concrete, concrete block, light weight concrete, concrete & ceramic roof tiles, sandstone, limestone, slate, hebel®, mortar joints, and compressed fibre cement sheet.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Saw BladesBORDO Diamond Saw Blades Hard Brick & Masonry
- 350mm Segmented Diamond Hard Brick Blade
- Hard brick and masonry.
- 10mm segmented rim for fast cutting with enhanced blade/substrate interface cooling for long blade life.
- Optimally designed for cutting cured concrete and stone.
- Extreme concentration of diamond for fast, clean cutting and long blade life.
- Can be used for either wet or dry cutting. Extended blade life will be experienced with wet cutting.
- Use when cutting bluestone, hard clay brick, fire brick, cured concrete, concrete block, concrete brick, granite, marble, wall chasing in hard brick & concrete.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews) -
Saw BladesBORDO Diamond Saw Blades PCD Saw Blades
- Enduro Polycrystalline Diamond (PCD) – cement sheet, plasterboard, MDF, chipboard, plywood & plastic.
- High speed, low dust cutting in fibre cement and blue board.
- Available in 160mm to 305mm.
- Extremely hard and durable polycrystalline diamond (PCD) teeth for extreme blade life.
- Thin kerf design combined with a low tooth count ensures high speed cutting and reduced dust compared with continuous rim diamond blades.
- Designed to cut fibre cement products, plasterboard, MDF, chipboard, plywood and plastic.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Saw BladesBORDO Diamond Saw Blades Super Turbo
- Enduro Diamond Super Turbo Fast Cut General Purpose
- Turbo blades typically have soft to medium bonds for a variety of general purpose to specific cutting applications.
- Turbo blades feature a continuous rim with an edge that is serrated.
- This serrated edge is designed to give the blade faster cutting speeds while maintaining a smooth cut, combining the best qualities from both segmented and continuous rim blades.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Saw BladesBORDO Diamond Saw Blades Tradecut Diamond Continuous Rim
- Tradecut Diamond Saw Continuous Rim
- Continuous rim blades have softer bonds for cutting hard materials such as tile, porcelain, granite, stone, glass, and other materials that can chip easily.
- These blades don’t have individual segments but instead have a solid, continuous rim or edge.
- Most continuous rim blades are designed for wet cutting applications, providing the smoothest, chip free cuts.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Saw BladesBORDO Diamond Saw Blades Tradecut Diamond Segmented Rim
- Tradecut Diamond Segmented Rim
- High diamond count for long blade life.
- Segmented rim for clean, fast cuts both wet and dry.
- Free cutting with reduced vibration.
- Efficient slurry evacuation.
- Use to cut cured concrete, reinforced concrete, clay bricks, Hebel®, terracotta tiles, slate, granite, bluestone, fibreglass, reinforced plastics, wall chasing in brick and concrete.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Saw BladesBORDO Diamond Saw Blades Tradecut Diamond Turbo
- Tradecut Diamond Saw Turbo Rim
- Turbo blades typically have soft to medium bonds for a variety of general purpose to specific cutting applications.
- Turbo blades feature a continuous rim with an edge that is serrated.
- This serrated edge is designed to give the blade faster cutting speeds while maintaining a smooth cut, combining the best qualities from both segmented and continuous rim blades.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Saw BladesBORDO Diamond Saw Blades Ultra Thin
- Ultra thin turbo rim general purpose
- Ultra thin 1.2mm kerf removes less material for super fast cutting and reduced wastage.
- The serrated edge is designed to give the blade faster cutting speeds while maintaining a smooth cut, combining the best qualities from both segmented and continuous rim blades.
- Extreme concentration of diamond for fast, clean cutting and long blade life.
- 8mm segment height provides the benefits of fast cutting with maximum control for superior cut accuracy.
- Can be used for either wet or dry cutting. Extended blade life will be experienced with wet cutting.
- Ideal for use in tile saws and angle grinders.
- Fast cutting with reduced chipping.
- Use when cutting porcelain, ceramic tiles, vitrified tiles, glazed tiles, terracotta, granite, marble, slate, limestone and sandstone.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Tap & DiesBORDO Die Holder
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Drill Bits/SetsBORDO Double Brick Straight Shank TCT Masonry Drill
- Double brick, straight shank, general purpose masonry drill.
- Premium grade tungsten carbide.
- High temperature brazing for longer bit life.
- Flutes designed for optimal spoil removal.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Drill Bits/SetsBORDO Drill Adaptor
- Bordo Power-Hex Drill Adaptors convert standard round shank Twist drills to 1/4″ hex shank.
- The resulting hex shank drill is suitable for use in quick change adaptors, bit holders and standard drill chucks.
- Select the correct size Power-Hex Drill Adaptor to suit the drill you wish to convert.
- Loosen the collet on the adaptor and fully insert the drill into the adaptor.
- Tighten the adaptor with a spanner or adjustable wrench to ensure that there is no slip.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Drill Bits/SetsBORDO Drill Adaptor Sets
- Bordo Power-Hex Drill Adaptors convert standard round shank Twist drills to 1/4″ hex shank.
- The resulting hex shank drill is suitable for use in quick change adaptors, bit holders and standard drill chucks.
- Select the correct size Power-Hex Drill Adaptor to suit the drill you wish to convert.
- Loosen the collet on the adaptor and fully insert the drill into the adaptor.
- Tighten the adaptor with a spanner or adjustable wrench to ensure that there is no slip.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Drill Bits/SetsBORDO Drill Chuck
- DRILL CHUCK – UP TO 7MM
- For firm grip of small drill bits (up to 7mm).
- Hex shank eliminates chuck slip.
(0 reviews) -
Hole Saws/KitsBORDO Drilling Template with Suction
- Drilling Template with Suction
- Drilling Template 4-83mm
- The Bordo heavy duty drilling template fixes securely to any smooth surface with a simple lever actuated suction function.
- The 2715-HT template is suitable for use with hole saws and drills from 4 to 83mm.
(0 reviews) -
BrushwareBORDO Drive Arbour
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BORDOBORDO Dual Mode ES200 Electric Screwdriver
- Electric Mode 2 Nm.
- Manual Mode 10 Nm.
- Speed 280 RPM.
- Charge 3.6 V USB.
- Auto on LEC task light.
- Includes Phillips#2 / Slot 6mm double ended bit.
- Includes USB charging cable.
(0 reviews) -
BurrsBORDO E-Z Chamfer Hex Shank De-Burring & Chamfering Tool
- 18-38mm E-Z Chamfer hex shank de-burring and chamfering tool
- 18-38mm (23/32-1.1/2″) capacity.
- E-Z Chamfer efficiently removes burrs and ridges from bolts, pipe, threaded rod, bar and dowels. It is suitable for use on metals including mild and hardened steels, stainless steel, copper and brass, as well as timber, fibreglass and plastics.
- E-Z Chamfer prevents sparks and burns. When used correctly at low RPMs the tool will not overheat the workpiece. Threads and burrs are sheared off creating the perfect chamfer for starting a nut or threading die.
- Unique patented design!
- World first M2-HSS Chamfer Tool!
- Heavy duty single piece construction!
- Suitable for use on ferrous and non-ferrous metals including MILD STEEL – U.S. Grade 2 – Metric Grade 4.8
- Suitable for use on ferrous and non-ferrous metals including HARD STEEL – U.S. Grade 5 – Metric Grade 8.8
- Suitable for use on ferrous and non-ferrous metals including VERY HARD STEEL – U.S. Grade 8 – Metric Grade 10.9
- Suitable for use on ferrous and non-ferrous metals including STAINLESS STEEL – 300 Series
(0 reviews) -
BrushwareBORDO End Brush Crimp Steel Wire High Speed
- End brushes are used for industrial applications where space is an issue.
- These brushes are typically used with a high speed hand-held tool, such as a die grinder, for applications including cleaning, polishing, deburring and surface preparation.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BrushwareBORDO End Brush Twist Knot 316 Stainless Wire High Speed
- End brushes are used for industrial applications where space is an issue.
- These brushes are typically used with a high speed hand-held tool, such as a die grinder, for applications including cleaning, polishing, deburring and surface preparation.
(0 reviews) -
Brushware
BORDO End Brush Twist Knot Steel Wire High Speed
- End brushes are used for industrial applications where space is an issue.
- These brushes are typically used with a high speed hand-held tool, such as a die grinder, for applications including cleaning, polishing, deburring and surface preparation.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Milling CuttersBORDO End Mills Fractional Long – Threaded
- HSS-Co8 (Cobalt) end cutting, long threaded
- End Mills can cut in both axial and radial directions.
- End mills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Four flutes (6 in larger diameters) result in a high quality surface finish.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Milling CuttersBORDO End Mills Fractional Short – Threaded
- HSS-Co8 (Cobalt) end cutting, short threaded
- End Mills can cut in both axial and radial directions.
- End mills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Four flutes (6 in larger diameters) result in a high quality surface finish.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Milling CuttersBORDO End Mills Fractional Short – Threaded 6 Piece Set
- 6 Piece Fractional Short Threaded End Mill Set
- HSS-Co8 (Cobalt) end cutting, short threaded
- End Mills can cut in both axial and radial directions.
- End mills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Four flutes (6 in larger diameters) result in a high quality surface finish.
(0 reviews) -
Milling CuttersBORDO End Mills Metric Long – Plain Flatted
- HSS-Co8 (Cobalt) end cutting, long flatted
- End Mills can cut in both axial and radial directions.
- End mills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Four flutes (6 in larger diameters) result in a high quality surface finish.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Milling Cutters
BORDO End Mills Metric Long – Threaded
- HSS-Co8 (Cobalt) end cutting, long threaded
- End Mills can cut in both axial and radial directions.
- End mills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Four flutes (6 in larger diameters) result in a high quality surface finish.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Milling Cutters
BORDO End Mills Metric Short – Plain Flatted
- HSS-Co8 (Cobalt) end cutting, short flatted
- End Mills can cut in both axial and radial directions.
- End mills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Four flutes (6 in larger diameters) result in a high quality surface finish.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Milling Cutters
BORDO End Mills Metric Short – Plain Flatted 6 Piece Set
- 6 Piece Metric Short Flatted End Mill Set
- HSS-Co8 (Cobalt) end cutting, short flatted
- End Mills can cut in both axial and radial directions.
- End mills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Four flutes (6 in larger diameters) result in a high quality surface finish.
(0 reviews) -
Milling Cutters
BORDO End Mills Metric Short – Threaded
- HSS-Co8 (Cobalt) end cutting, short threaded
- End Mills can cut in both axial and radial directions.
- End mills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Four flutes (6 in larger diameters) result in a high quality surface finish.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Milling Cutters
BORDO End Mills Metric Short – Threaded 6 Piece Set
- 6 Piece Metric Short Threaded End Mill Set
- HSS-Co8 (Cobalt) end cutting, short threaded
- End Mills can cut in both axial and radial directions.
- End mills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Four flutes (6 in larger diameters) result in a high quality surface finish.
(0 reviews) -
Milling CuttersBORDO End Mills Metric Single Flute Short – Round Shank
- HSS-Co8 (Cobalt) end cutting, round shank.
- Centre cutting for straight plunging or ramping.
- End Mills can cut in both axial and radial directions.
- For applications requiring fast, high-volume material removal, the single flute design is ideal.
- Our single flute tools are highly versatile – excelling at roughing.
- These tools are perfect for aluminium, brass, plastics, exotic composites and any soft metals.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BurrsBORDO Express Cut Ball 1/4″ Shank Diameter
- Express Cut Burrs (also referred to as Double Cut Burrs) are general purpose burrs designed for rapid stock removal and improved operator control.
- Chip size is reduced and lower tool speeds can be used compared with standard cut burrs.
- Ideal for use in carbon steel, cast iron, high strength steel, stainless steel, steel castings, steel welds, titanium alloy and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Burrs
BORDO Express Cut Ball 1/8″ Shank Diameter
- Express Cut Burrs (also referred to as Double Cut Burrs) are general purpose burrs designed for rapid stock removal and improved operator control.
- Chip size is reduced and lower tool speeds can be used compared with standard cut burrs.
- Ideal for use in carbon steel, cast iron, high strength steel, stainless steel, steel castings, steel welds, titanium alloy and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Burrs
BORDO Express Cut Ball Long 1/4″ Shank Diameter
- Express Cut Burrs (also referred to as Double Cut Burrs) are general purpose burrs designed for rapid stock removal and improved operator control.
- Chip size is reduced and lower tool speeds can be used compared with standard cut burrs.
- Ideal for use in carbon steel, cast iron, high strength steel, stainless steel, steel castings, steel welds, titanium alloy and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BurrsBORDO Express Cut Cylindrical 1/4″ Shank Diameter
- SA-11 Express cut tungsten carbide burr.
- 6.35mm (1/4″) Shank.
- Express Cut Burrs (also referred to as Double Cut Burrs) are general purpose burrs designed for rapid stock removal and improved operator control.
- Chip size is reduced and lower tool speeds can be used compared with standard cut burrs.
- Ideal for use in carbon steel, cast iron, high strength steel, stainless steel, steel castings, steel welds, titanium alloy and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Burrs
BORDO Express Cut Cylindrical 1/8″ Shank Diameter
- SA-41 Express cut tungsten carbide burr.
- 1/8″ Shank.
- Express Cut Burrs (also referred to as Double Cut Burrs) are general purpose burrs designed for rapid stock removal and improved operator control.
- Chip size is reduced and lower tool speeds can be used compared with standard cut burrs.
- Ideal for use in carbon steel, cast iron, high strength steel, stainless steel, steel castings, steel welds, titanium alloy and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page