Material Handling
Showing 361–396 of 472 results
-
Garage JacksTQB BRANDS Air Jack/Support Stand 10,000kg
This Borum “Industrial Quality” heavy-duty 10,000kg Air Jack/Support Stand runs entirely on compressed air. Air acts straight onto the piston to raise the load, and you control it with a simple UP/DOWN air valve. It’s a reinforced pin-style jack and stand built to take heavy loads up to 10,000kg, which makes it ideal for serviciing trucks, buses, farm gear and earthmoving equipment. It adjusts to suit the job, with a 444mm minimum height (536mm once the locking pins are in), 292mm of lift, and up to 1298mm using the extension tube.
To reach the full 10,000kg it needs a 200psi air supply. Anything less lifts a lighter load.
It’s built from high-grade steel and runs a sealed piston-and-cylinder setup. The piston and ram are hardened, treated and polished, so they stand up to heavy, repeat use.
Once it’s up at the right height, the load locks onto the steel pins, so it isn’t sitting on air pressure alone. The manual is firm on this: pin the post and exhaust the air before anyone works on, under or around the load. A safety valve and an exhaust silencer are built into the air circuit.
The whole unit is built for hard industrial use. A rugged steel frame is finished in lead-free paint across every surface to handle long-term wear and help keep rust at bay. That finish also shrugs off oil, grease and dirt, so it wipes clean in seconds.
Built with the best components from the highest grades of rugged steel, to the wear-resistant advanced technology sealing rings and a heavy duty hydraulic pump that’s filled with industrial grade high/low temperature-resistant hydraulic oil.
Features:
- Runs entirely on compressed air, acting straight onto the piston
- Simple UP/DOWN air valve to raise and lower
- Full 10,000kg lift needs a 200psi air supply; lower pressure lifts less
- Doubles as a pin-style support stand, so the load locks onto the pins
- Reinforced industrial design with support bracing
- Solid heavy-duty steel construction
- Hardened piston and ram, treated and polished
- Sealing rings on the piston and cylinder
- Built-in safety valve
- Exhaust silencer
- Height adjusts on locking pins, with an extension tube and height adaptors
- Lead-free paint to resist wear and help prevent rust
- Oil, grease and dirt resistant finish that wipes clean
Specifications:
- Safe Working Capacity: 10,000kg
- Minimum Height: 444mm
- Minimum Height With Locking Pins In Place: 536mm
- Maximum Height: 1298mm
- Hydraulic Lift: 292mm
- Base Diameter: 339mm
- Saddle Dimensions (ID): 100L x 100W x 29H mm
- Air Supply Pressure: 200psi (Required for full 10,000kg; lower pressure lifts less)
- Nett Weight: 79kg
- Crate: 640(L) x 390(W) x 590(H)mm
- Gross Weight: 91kg
Intended Use
Made for professional heavy-duty work across trucks, buses, agricultural, earthmoving, mining, rail and fleet maintenance. Anywhere you need to lift, support and lower big loads.
(0 reviews) -
Bottle JacksTQB BRANDS Air/Hydraulic Bottle Jack 20,000kg
This heavy duty 20,000kg Borum Industrial Air/Manual Bottle Jack packs a big punch, providing enough lifting power for use with farm vehicles, heavy-duty machinery, industrial construction equipment and more. The 2 piece removable handle is long enough to lift the load with ease and also helps to position the jack. Use this workhorse with a 90-120psi rated air pressure supply to lighten the load and provide the fast, strong lifting power you need, or operate it manually for normal operation just about anywhere.
Our Borum Industrial Quality Air/Manual Bottle Jacks are designed to operate either manually or pneumatically. The manual function allows for normal operation anywhere, even without an air supply.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- Manufactured of superior-grade steel to exacting standards for quality and durability
- Industrial quality hydraulic cylinder unit operates at lower oil pressure to raise load, reduce wear and extend service life
- Precision machined, chrome plated and polished piston-ram
- CNC machined ports and threads
- Built-in hydraulic by-pass protection against over pumping damage
- Versatile “quick connector” design for easy removal of air hose for compact storage or remote operation
- Compact yet powerful Industrial Quality Air Turbo Motor
- Lead-free paint is applied to ensure a long-lasting finish and prevent corrosion
- Paint finish is oil, grease and dirt-resistant for easy cleanup
- Thick welded base for heavy duty use & longevity
Specifications:
- Safe Working Capacity: 20,000kg
- Minimum Height: 263mm
- Maximum Height: 503mm
- Hydraulic Lift: 160mm
- Adjustable Height: 80mm
- Base Area: 200 x 152mm
- Operating Air Pressure: 90-120psi
- Air Inlet Fitting: 1/4″ x 18NPT
- Nett Weight: 16.5kg
- Carton: 280 x 200 x 280mm
- Gross Weight: 17kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For professional heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Air/Hydraulic Bottle Jack 30,000kg
This heavy duty 30,000kg Borum Industrial Air/Manual Bottle Jack packs a big punch, providing enough lifting power for use with farm vehicles, heavy-duty machinery, industrial construction equipment and more. The 2 piece removable handle is long enough to lift the load with ease and also helps to position the jack. Use this workhorse with a 90-120psi rated air pressure supply to lighten the load and provide the fast, strong lifting power you need, or operate it manually for normal operation just about anywhere.
Our Borum Industrial Quality Air/Manual Bottle Jacks are designed to operate either manually or pneumatically. The manual function allows for normal operation anywhere, even without an air supply.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- Manufactured of superior-grade steel to exacting standards for quality and durability
- Industrial quality hydraulic cylinder unit operates at lower oil pressure to raise load, reduce wear and extend service life
- Precision machined, chrome plated and polished piston-ram
- CNC machined ports and threads
- Built-in hydraulic by-pass protection against over pumping damage
- Versatile “quick connector” design for easy removal of air hose for compact storage or remote operation
- Compact yet powerful Industrial Quality Air Turbo Motor
- Lead-free paint is applied to ensure a long-lasting finish and prevent corrosion
- Paint finish is oil, grease and dirt-resistant for easy cleanup
- Thick welded base for heavy duty use & longevity
Specifications:
- Safe Working Capacity: 30,000kg
- Minimum Height: 275mm
- Maximum Height: 532mm
- Hydraulic Lift: 162mm
- Adjustable Height: 95mm
- Base Area: 229 x 180mm
- Jack Lifting Saddle Diameter: 57mm
- Operating Air Pressure: 90-120psi
- Air Inlet Fitting: 1/4″ x 18NPT
- Nett Weight: 25.3kg
- Carton: 290 x 180 x 300mm
- Gross Weight: 26kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For professional heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Transmission LiftersTQB BRANDS Auxiliary Lifter 500kg
This 500kg capacity TradeQuip “Made for the Trade” Hydraulic Telescopic Auxiliary Lifter has a 4 prong mounting cradle suitable for partial temporary support of vehicle components. The foot-operated quick lift pump frees up operator’s hands when positioning for lift and the hand operated lowering mechanism provides safety with its extra slow lower control.
Not intended for supporting loads and not intended as a stand alone transmission lifter
Features
- Designed for partial temporary support of vehicle components during removal and installation of components
- Nylon wheels and full swivel ball bearing castors for easy movement
- High polished chrome-plated rams provides smooth operation to maximise its high reach that is lifted by the user-friendly hand release pedal
- 4 prong mounting cradle
- Included “cup” style saddle for smaller areas of work
- Unique hand release knob provides extra slow control safety when lowering
Specifications
- Safe Working Capacity: 500kg
- Minimum Height: 1175mm
- Maximum Height: 1985mm
- Cradle Size: 362 x 362mm
- Lift Pad Accessory: 107.5mm Dia
- Base Dimensions: 540 x 570mm
- Nett Weight: 35.5kg
- Crate: 1110 x 320 x 275mm
- Gross Weight: 37kg
Intended Use
Designed for partial temporary support of vehicle components during removal and installation of components. Not intended for supporting loads and not intended as a stand alone transmission lifter.
(0 reviews) -
Transmission LiftersTQB BRANDS Auxiliary Lifter Kit 500kg
This 500kg capacity TradeQuip “Made for the Trade” Hydraulic Telescopic Auxiliary Lifter kit is ideal for partial temporary support of vehicle components in a busy workshop. The foot-operated quick lift pump frees up operator’s hands when positioning for lift and the hand operated lowering mechanism provides safety with its extra slow lower control.
Not intended for supporting loads and not intended as a stand alone transmission lifter
Features
- Designed for partial temporary support of vehicle components during removal and installation of components
- Nylon wheels and full swivel ball bearing castors for easy movement
- High polished chrome-plated rams provides smooth operation to maximise its high reach that is lifted by the user-friendly hand release pedal
- 4 prong mounting cradle
- Included “cup” style lift pad for smaller areas of work
- Included adjustable fuel tank adaptor to provide extra stability
- Unique hand release knob provides extra slow control safety when lowering
Specifications
- Safe Working Capacity: 500kg
- Minimum Height: 1175mm
- Maximum Height: 1985mm
- Cradle Size: 362 x 362mm
- Lift Pad Accessory: 107.5mm Dia
- Fuel Tank Holder: 812 x 352mm
- Base Dimensions: 540 x 570mm
- Nett Weight: 35.3kg
- Crate: 1110 x 315 x 275mm
- Gross Weight: 52kg
Intended Use
Designed for partial temporary support of vehicle components during removal and installation of components. Not intended for supporting loads and not intended as a stand alone transmission lifter.
(0 reviews) -
Stands & RampsTQB BRANDS Auxiliary Stand 7,000kg
The BORUM Industrial Heavy Duty Auxiliary Stand is a reinforced pin style vehicle stand with a heavy duty design and support bracing system to sustain heavy vehicle loads up to 7,000kg. It’s adjustable to match the job with a 1255mm minimum lift height and 1905mm maximum lift height !! Featuring Heavy-Duty Industrial design, this tough stand is ideal for use under 2 post and 4 post vehicle lifts. With adjustable height increments, 3 choices of saddle attachments, and a stable tripod design, the feet (with base plates) securely hold this auxiliary stand in place when the spring loaded swivel castor wheels are under load. This heavy duty stand is mobile when needed and stable under load, so its a very handy peice of equipment when working under a vehicle lift. This tripod design ensures complete stability, even when your workshop floor is not perfectly flat.
Features
- Heavy duty design and support bracing system to sustain heavy ve
hicle loads - Manufactured from high-grade steel and built to exacting standards for quality and durability
- Fitted with spring loaded castor wheels to ensure easy movement around the workshop
- Fitted with spring loaded support beam
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting finish and to help prevent rust
- Paint is oil, grease and dirt-resistant for easy cleanup
- High strength locking pin
- Controlled pin holes for easy height adjustments
- Turned post slide for easy quick adjustments
Specifications
- Safe Working Capacity: 7,000kg
- Maximum Height: 1905mm
- Minimum Height: 1295mm
- 3 saddle options: 90mm, 120mm, up to 150mmØ
- Adjustable Pin Heights: 8 (75mm increments)
- Distance between Caster wheels: 630mm (Centre wheel to centre wheel measurement)
- Nett Weight: 65kg
- Carton: 1130 x 370 x 320mm
- Weight: 68kg
Intended Use
To support and/or stabilise a vehicle that is raised by a 2or4 post hoist or in-ground lift. Should always be used in pairs.
NOTE: Sold individually but recommended to be used in pairs
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use jack stands.
(0 reviews) - Heavy duty design and support bracing system to sustain heavy ve
-
Bottle JacksTQB BRANDS Bottle Jack 10,000kg
This powerful, heavy-duty TradeQuip “Made for the Trade” Hydraulic Bottle Jack with high quality glide-action pressure pump is designed for hard-hitting commercial use, making large loads easy to lift. The lightweight jack is ideal for lifting farm vehicles, heavy-duty machinery, industrial construction equipment and more. High quality, fitted with unique overload protection system and large stable base. Supplied with 500mm pump handle.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features
- Machined and polished cylinders with die-cut threads provide non-abrasive leak-free, durable performance
- Fabricated from hard-cast steel with heat-treated critical stress areas
- Unique cross-type forged release valve assures positive load control
- Overload protection Hydraulic system is protected from internal damage by a by-pass mechanism
Specifications
- Safe Working Capacity: 10,000kg
- Hydraulic Lift: 130mm
- Adjustable Screw Height: 65mm
- Minimum Height: 200mm
- Maximum Height: 395mm
- Base Area: 124 x 124mm
- Handle: 500 x 20mm
- Carton: 140 x 135 x 215mm (plus handle)
- Gross Weight: 6kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack 15,000kg
This powerful, heavy-duty TradeQuip Hydraulic Bottle Jack with high quality glide-action pressure pump is designed for hard-hitting commercial use, making large loads easy to lift. The lightweight jack is ideal for lifting farm vehicles, heavy-duty machinery, industrial construction equipment and more. High quality, fitted with unique overload protection system and large stable base. Supplied with 500mm pump handle.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- Machined and polished cylinders with die-cut threads provide non-abrasive leak-free, durable performance
- Fabricated from hard-cast steel with heat-treated critical stress areas
- Unique cross-type forged release valve assures positive load control
- Overload protection
- Hydraulic system is protected from internal damage by a by-pass mechanism
- Meets ASNZS2693:1993 safety standards
Specifications
- Safe Working Capacity: 15,000kg
- Hydraulic Lift: 150mm
- Adjustable Screw Height: 60mm
- Minimum Height: 230mm
- Maximum Height: 440mm
- Base Area: 148 x 136mm
- Handle: 500 x 20mm
- Carton: 160 x 145 x 235mm (plus handle)
- Gross Weight: 9kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack 20,000kg
This powerful, heavy-duty TradeQuip “Made for the Trade” Hydraulic Bottle Jack with high quality glide-action pressure pump is designed for hard-hitting commercial use, making large loads easy to lift. The lightweight jack is ideal for lifting farm vehicles, heavy-duty machinery, industrial construction equipment and more. High quality, fitted with unique overload protection system and large stable base. Supplied with 500mm pump handle.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- Machined and polished cylinders with die-cut threads provide non-abrasive leak-free, durable performance
- Fabricated from hard-cast steel with heat-treated critical stress areas
- Unique cross-type forged release valve assures positive load control
- Overload protection
- Hydraulic system is protected from internal damage by a by-pass mechanism
Specifications
- Safe Working Capacity: 20,000kg
- Hydraulic Lift: 160mm
- Adjustable Screw Height: 60mm
- Minimum Height: 240mm
- Maximum Height: 460mm
- Base Area: 167 x 156mm
- Handle: 500 x 20mm
- Carton: 175 x 165 x 255mm (plus handle)
- Gross Weight: 12kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Air/Hydraulic 12,000kg
This TradeQuip “Made for the Trade” Air/ Hydraulic Bottle Jack is designed to operate pneumatically. The power of air makes it easy to lift farm vehicles, trucks, lawn mowers, heavy duty machinery, industrial construction equipment and more. With it’s low profile design this 12,000kg heavy-duty air/hydraulic bottle jack is the perfect choice for a wide variety of uses. Use this workhorse with a 110-125 PSI rated air pressure supply to lighten the load and provide the fast, strong lifting power you need. The 260–510mm lift range raises the load to the desired height and a knurled, heat-treated pad with screw height adjustment allows fine-tune of the jack from there.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- Machined and polished cylinders with die-cut threads
- Fabricated from hard-cast steel with heat-treated critical stress areas
- Unique cross-type forged release valve assures positive load control
- Built-in bypass protection prevents damage from over pumping
- Compact yet powerful Air Turbo motor
- Versatile “quick connector provides ‘quick & easy air connection
- Two piece pump handle
- Convenient welded carry handle
Specifications:
- Safe Working Capacity: 12,000kg
- Minimum Height: 260mm
- Maximum Height: 510mm
- Hydraulic Stroke: 170mm
- Screw Extension Height: 80mm
- Operating Air Pressure: 110-125psi
- Air Fitting: 1/4″
- Carton: 250x180x270mm
- Gross Weight: 12.75kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Air/Hydraulic 20,000kg
Our TradeQuip “Made for the Trade” Air/Manual 20,000kg Bottle Jack is designed to operate either manually or pneumatically. The manual function allows for normal operation anywhere, even without an air supply. Ideal for onsite/offsite lifting of farm vehicles, heavy duty machinery, industrial construction equipment and more. The Air/Manual Bottle Jack is equipped with an hydraulic system and a mounted powerful manual pump. Used on light or heavy vehicles, they are compact, versatile and safe to use. Our TradeQuip “Made for the Trade” design includes a quality safety valve to prevent overloading and a larger base to provide high safety and greater stability. This Air/Manual Bottle Jack is fitted with a Professional Quality Air Turbo Motor designed to meet the demands of adverse climate conditions and extreme temperatures. This ‘Best Selling’ Jack is a favourite of the Qld and WA mine maintenance crews, due to it’s strong lifting power and long lasting wear characteristics.
This 20,000kg heavy-duty air/hydraulic bottle jack is the perfect choice for a wide variety of uses. The power of air makes it easy to lift farm vehicles, trucks, trailers, heavy equipment and other large loads! Use this workhorse with a 90-120 PSI rated air pressure supply to lighten the load and provide the fast, strong lifting power you need, or operate it manually for normal operation just about anywhere. The 265–430mm lift range raises the load to the desired height and a knurled, heat-treated pad with 100mm screw height adjustment allows you to fine-tune the jack from there.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Always consider the TradeQuip Air Turbo Motor Features:
- Best practise quality controlled manufacturing process
- CNC machined cast alloy piston and barrel
- Barrel is hardness rated opposed to other mild steel variations
- Piston & Barrel combination present longlife wear characteristics similar to an engine crank and bearing
- Duro70 rated nitrile O’rings (best for air tool applications) provide good elasticity and friction rating
- Results in longer duty cycle over adverse Australian climate and temperature ranges
- Superior lithium grease lubrication is less prone to drying or flushing out from wet ,dry, hot or cold air supplies
- Lithium grease re-emulsifies when a few drops of air tool oil or 32 grade hydraulic oil is regularly added
Specifications
- Safe Working Capacity: 20,000kg
- Minimum Height: 265mm
- Maximum Height: 510mm
- Hydraulic Lift: 170mm (265mm to 435mm)
- Adjustable Height: 75mmn (Maximum height 510mm)
- Base Area: 224x134mm
- Work Pressure: 90-120psi
- Carton: 290 x 200 x 290mm
- Weight: 16kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Air/Hydraulic 20,000kg
This TQ Pro “Latest Applied Technologies” 20,000kg Air/Hydraulic Bottle Jack is constructed of superior grade steel and built to premium standards for quality and durability. The superior-quality, large diameter hydraulic steel cylinder unit results in lower oil pressure needed to raise the load. A built-in bypass device protects the hydraulic system from over-pumping damage. The sturdy and stable design features a welded base and cylinder to assure strength and eliminate leaks.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features
- Using CNC technology, the frame is constructed using superior-grade steel and built to premium TQ Pro standards for professional quality and durability
- Premium quality large diameter hydraulic steel cylinder with precision tolerances
- Piston-ram is treated and polished to minimise wear and extend service life
- High capability premium quality seal system efficiently protects internal hydraulics keeping it free from contaminants
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting premium finish
- Paint is oil, grease and dirt-resistant for easy cleanup
- Thick Base Design
The thick base design is to provide the firmest footprint reducing flex. This substantially increases the life of the hydraulic ram under the toughest lifting and lowering circumstances.
Welded Reservoir
A welded reservoir instead of the screw base results in a substantial increase in durability. With the completely sealed hydraulic system, wear and tear and internal contamination is dramatically reduced.
Specifications
- Safe Working Capacity: 20,000kg
- Maximum Height: 525mm
- Minimum Height: 261.5
- Hydraulic Lift: 156mm
- Adjustable Lift: 95mm
- Operating Air Pressure: 110-125psiAir Inlet Fitting: 1/4″
- Base Dimensions: 230 x 150 x 30mm
- Carton: 270 x 240 x 290mm
- Nett Weight: 19kg
- Gross Weight: 22kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For professional specialist use on truck, agriculture, construction, mining, mobile home, oil field, automotive, and marine applications where lifting is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Air/Hydraulic 30,000kg
This TQ Pro “Latest Applied Technologies” 30,000kg Air/Hydraulic Bottle Jack is constructed of superior grade steel and built to premium standards for quality and durability. The premium-quality, large diameter hydraulic steel cylinder unit results in lower oil pressure needed to raise the load. A built-in bypass device protects the hydraulic system from over-pumping damage. The sturdy and stable design features a welded base and cylinder to assure strength and eliminate leaks.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features
- Using CNC technology, the frame is constructed using superior-grade steel and built to premium TQ Pro standards for professional quality and durability
- Premium quality large diameter hydraulic steel cylinder with precision tolerances
- Piston-ram is treated and polished to minimise wear and extend service life
- High capability premium quality seal system efficiently protects internal hydraulics keeping it free from contaminants
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting premium finish
- Paint is oil, grease and dirt-resistant for easy cleanup
Thick Base Design
The thick base design is to provide the firmest footprint reducing flex. This substantially increases the life of the hydraulic ram under the toughest lifting and lowering circumstances.
Welded Reservoir
A welded reservoir instead of the screw base results in a substantial increase in durability. With the completely sealed hydraulic system, wear and tear and internal contamination is dramatically reduced.
Specifications
- Safe Working Capacity: 30,000kg
- Maximum Height: 533mm
- Minimum Height: 279.5mm
- Hydraulic Lift: 155mm
- Adjustable Screw Height: 95mm
- Operating Air Pressure: 110-125psi
- Air Inlet Fitting: 1/4″
- Base Dimensions: 250 x 180 x 40mm
- Carton: 270 x 240 x 290mm
- Nett Weight: 29kg
- Gross Weight: 29.5kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For professional specialist use on truck, agriculture, construction, mining, mobile home, oil field, automotive, and marine applications where lifting is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Air/Hydraulic 35,000kg
This powerful heavy duty 35,000kg Borum Industrial Air/Hydraulic Bottle Jack packs a big punch, providing enough lifting power for use with farm vehicles, heavy-duty machinery, industrial construction equipment and more. The 2 piece removable handle is long enough to lift the load with ease and also helps to position the jack. Use this workhorse with a 110-125psi rated air pressure supply to lighten the load and provide the fast, strong lifting power you need, or operate it manually for normal operation just about anywhere.
Our Borum Industrial Quality Air/Manual Bottle Jacks are designed to operate either manually or pneumatically. The manual function allows for normal operation anywhere, even without an air supply.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
(Previous models include product code/s; 35TABJ)
Features:
- Manufactured of superior-grade steel to exacting standards for quality and durability
- Industrial quality hydraulic cylinder unit operates at lower oil pressure to raise load, reduce wear and extend service life
- Precision machined, chrome plated and polished piston-ram
- CNC machined ports and threads
- Built-in hydraulic by-pass protection against over pumping damage
- Versatile “quick connector” design for easy removal of air hose for compact storage or remote operation
- Compact yet powerful Industrial Quality Air Turbo Motor
- Lead-free paint is applied to ensure a long-lasting finish and prevent corrosion
- Paint finish is oil, grease and dirt-resistant for easy cleanup
Specifications:
- Safe Working Capacity: 35,000kg
- Minimum Height: 264mm
- Maximum Height: 414mm
- Hydraulic Stroke: 150mm
- Base Area: 210x280mm
- Operating Air Pressure: 110-125psi
- Air Inlet Fitting: 1/4″ x 18NPT
- Nett Weight: 29kg
- Carton: 265 x 230 x 300mm
- Gross Weight: 30kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For professional heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Air/Manual 20,000kg
This heavy duty 20,000kg eQuipt Air/Manual Bottle Jack packs a big punch, providing enough lifting power for use with farm vehicles, heavy-duty machinery, industrial construction equipment and more. The 2 piece removable handle is long enough to lift the load with ease and also helps to position the jack. Use this workhorse with a 110-125psi rated air pressure supply to lighten the load and provide the fast, strong lifting power you need, or operate it manually for normal operation just about anywhere.
Our eQuipt Air/Manual Bottle Jacks are designed to operate either manually or pneumatically. The manual function allows for normal operation anywhere, even without an air supply.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- Manufactured of superior-grade steel to exacting standards for quality and durability
- Industrial quality hydraulic cylinder unit operates at lower oil pressure to raise load, reduce wear and extend service life
- Precision machined, chrome plated and polished piston-ram
- CNC machined ports and threads
- Built-in hydraulic by-pass protection against over pumping damage
- Versatile “quick connector” design for easy removal of air hose for compact storage or remote operation
- Compact yet powerful Industrial Quality Air Turbo Motor
- Lead-free paint is applied to ensure a long-lasting finish and prevent corrosion
- Paint finish is oil, grease and dirt-resistant for easy cleanup
Specifications:
- Safe Working Capacity: 20,000kg
- Minimum Height: 262mm
- Maximum Height: 504mm
- Hydraulic Stroke: 163mm
- Adjustable Screw: 79mm
- Operating Air Pressure: 110-125psi
- Air Inlet Fitting: 1/4″ x 18NPT
- Nett Weight: 16kg
- Carton: 275 x 190 x 290mm
- Gross Weight: 17kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For professional heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Air/Manual 20,000kg
This heavy duty 20,000kg Borum Industrial Air/Manual Bottle Jack packs a big punch, providing enough lifting power for use with farm vehicles, heavy-duty machinery, industrial construction equipment and more. The 2 piece removable handle is long enough to lift the load with ease and also helps to position the jack. Use this workhorse with a 110-125psi rated air pressure supply to lighten the load and provide the fast, strong lifting power you need, or operate it manually for normal operation just about anywhere.
Our Borum Industrial Quality Air/Manual Bottle Jacks are designed to operate either manually or pneumatically. The manual function allows for normal operation anywhere, even without an air supply.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- Manufactured of superior-grade steel to exacting standards for quality and durability
- Industrial quality hydraulic cylinder unit operates at lower oil pressure to raise load, reduce wear and extend service life
- Precision machined, chrome plated and polished piston-ram
- CNC machined ports and threads
- Built-in hydraulic by-pass protection against over pumping damage
- Versatile “quick connector” design for easy removal of air hose for compact storage or remote operation
- Compact yet powerful Industrial Quality Air Turbo Motor
- Lead-free paint is applied to ensure a long-lasting finish and prevent corrosion
- Paint finish is oil, grease and dirt-resistant for easy cleanup
Specifications:
- Safe Working Capacity: 20,000kg
- Minimum Height: 262mm
- Maximum Height: 504mm
- Hydraulic Stroke: 163mm
- Adjustable Screw: 79mm
- Operating Air Pressure: 110-125psi
- Air Inlet Fitting: 1/4″ x 18NPT
- Nett Weight: 16kg
- Carton: 275 x 190 x 290mm
- Gross Weight: 17kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For professional heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Squat 12,000kg
This powerful, heavy-duty TradeQuip “Made for the Trade” Hydraulic Bottle Jack with high quality glide-action pressure pump is designed for hard-hitting commercial use, making large loads easy to lift. The lightweight jack is ideal for lifting farm vehicles, heavy-duty machinery, industrial construction equipment and more. Professional quality, ideal for the workshop or panel shop. Fitted with unique overload protection system and large stable base. Supplied with 500mm pump handle. The low profile design of this hydraulic jack fits underneath tight spots. The jack drops down to just 180mm at its lowest point, making it ideal for use in automotive and ag repair shops, and other small spaces.
Attain the proper work height with the 85mm hydraulic lift range, and then do some fine tuning to get load exactly where you want it. The knurled heat-treated pad with 70mm screw adjustment offers the versatility you need. A convenient steel carrying handle makes it easy to transport the jack to any location. The stubby bottle jack is the perfect choice for everyday vertical lifting in a variety of environments. A lead-free paint finish covers the surface to ensure long-lasting wear and to help prevent rust. The paint is oil-, grease- and dirt-resistant for easy cleanup no matter how often you put this jack to work.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- Machined and polished cylinders with die-cut threads provide non-abrasive leak-free, durable performance
- Fabricated from hard-cast steel with heat-treated critical stress areas
- Unique cross-type forged release valve assures positive load control
- Overload protection
- Convenient welded carry handle
- Paint is oil, grease and dirt-resistant for easy cleanup
Specifications:
- Safe Working Capacity: 12,000kg
- Hydraulic Lift: 85mm
- Adjustable Screw Height: 55mm
- Minimum Height: 175mm
- Maximum Height: 315mm
- Base Area: 157 x 134mm
- Handle: 500 x 20mm
- Carton: 148 x 142 x 190mm (plus handle)
- Gross Weight: 7kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Squat 20,000kg
This powerful, heavy-duty TradeQuip “Made for the Trade” Hydraulic Bottle Jack with high quality glide-action pressure pump is designed for hard-hitting commercial use, making large loads easy to lift. The lightweight jack is ideal for lifting farm vehicles, heavy-duty machinery, industrial construction equipment and more. Professional quality, ideal for the workshop or panel shop. Fitted with unique overload protection system and large stable base. Supplied with 500mm pump handle. The low profile design of this hydraulic jack fits underneath tight spots. The jack drops down to just 200mm at its lowest point, making it ideal for use in automotive and ag repair shops, and other small spaces.
Attain the proper work height with the 110mm hydraulic lift range, and then do some fine tuning to get your load exactly where you want it — the knurled heat-treated pad with 75mm screw adjustment offers the versatility you need. A convenient steel carrying handle makes it easy to transport the jack to any location. The stubby bottle jack is the perfect choice for everyday vertical lifting in a variety of environments. A lead-free paint finish covers the surface to ensure long-lasting wear and to help prevent rust. The paint is oil-, grease- and dirt-resistant for easy cleanup no matter how often you put this jack to work.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- Machined and polished cylinders with die-cut threads provide non-abrasive leak-free, durable performance
- Fabricated from hard-cast steel with heat-treated critical stress areas
- Unique cross-type forged release valve assures positive load control
- Overload protection
- Convenient welded carry handle
Specifications
- Safe Working Capacity: 20,000kg
- Hydraulic Lift: 110mm
- Adjustable Screw Height: 60mm
- Minimum Height: 200mm
- Maximum height: 370mm
- Base Area: 167 x 156mm
- Handle: 500 x 20mm
- Carton: 180 x 165 x 210mm (plus handle)
- Gross Weight: 10kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Squat Air/Hydraulic 20,000kg
This TradeQuip “Made for the Trade” Air/ Hydraulic “Low Profile” Bottle Jack is designed to operate pneumatically. This unit provides enough lifting power for use with farm vehicles, heavy duty machinery, industrial construction equipment and more. It’s low profile design get’s you out of tight situations with ease. This 20,000kg heavy-duty air/hydraulic bottle jack with powerful heavy duty operation is the perfect choice for a wide variety of uses. The power of air makes it easy to lift farm vehicles, trucks, lawn mowers, heavy equipment and other large loads! Use this workhorse with a 100-145 PSI rated air pressure supply to lighten the load and provide the fast, strong lifting power you need. The 150–260mm lift range raises the load to the desired height and a knurled, heat-treated pad with screw height adjustment allows you to fine-tune the jack from there. This Bottle Jack is designed for day in and day out durability. A rugged high-grade steel frame is teamed with a lead-free paint finish that covers the entire surface to ensure long-lasting wear and help prevent rust. The paint is oil-, grease- and dirt-resistant for easy cleanup no matter how often you put this jack to work.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
Features:
- All air bottle jacks have chrome plated rams
- Built-in by-pass device protects hydraulic system from over pumping damage
- Versatile “quick connector” design provides for easy removal of air hose from air motor allowing compact storage or remote operation
- Compact yet powerful Air Turbo Motor
Specifications:
- Safe Working Capacity: 20,000kg
- Minimum Height: 148mm
- Maximum Height: 259mm
- Hydraulic Stroke: 66mm
- Screw Extension Height: 45mm
- Operating Air Pressure: 100-145psi
- Base Area: 201x135mm
- Carton: 355x165x165mm
- Gross Weight: 10kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Squat Air/Hydraulic 20,000kg
This TradeQuip “Made for the Trade” Air/ Hydraulic Bottle Jack is designed to operate pneumatically. The power of air makes it easy to lift farm vehicles, trucks, lawn mowers, heavy duty machinery, industrial construction equipment and more. With it’s low profile design this 20,000kg heavy-duty air/hydraulic bottle jack is the perfect choice for a wide variety of uses. Use this workhorse with a 110-125 PSI rated air pressure supply to lighten the load and provide the fast, strong lifting power you need. The 178–328mm lift range raises the load to the desired height and a knurled, heat-treated pad with screw height adjustment allows fine-tune of the jack from there.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
(Previous models include product code/s; BSLAJ20)
Features:
- Machined and polished cylinders with die-cut threads
- Fabricated from hard-cast steel with heat-treated critical stress areas
- Unique cross-type forged release valve assures positive load control
- Built-in bypass protection prevents damage from over pumping
- Compact yet powerful Air Turbo motor
- Versatile “quick connector provides ‘quick & easy air connection
- Two piece pump handle
- Convenient welded carry handle
Specifications:
- Safe Working Capacity: 20,000kg
- Minimum Height: 178mm
- Maximum Height: 328mm
- Hydraulic Stroke: 87mm
- Screw Extension Height: 63mm
- Operating Air Pressure: 110-125psi
- Air Fitting: 1/4″
- Carton: 390x192x195mm
- Gross Weight: 13kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For heavy duty use on truck, agriculture, construction, mining, automotive, and marine applications where lifting and lowering is required.
(0 reviews) -
Bottle JacksTQB BRANDS Bottle Jack Squat Air/Hydraulic 20,000kg
This TQ Pro “Latest Applied Technologies” 20,000kg Air/Hydraulic Bottle Jack is constructed of superior grade steel and built to premium standards for quality and durability. The premium-quality, large diameter hydraulic steel cylinder unit results in lower oil pressure needed to raise the load. A built-in bypass device protects the hydraulic system from over-pumping damage. The sturdy and stable design features a welded base and cylinder to assure strength and eliminate leaks.
Fitted with a safety overload valve for extra protection, the safety valve is installed between the pump and high-pressure check valve in the barrel/lift ram assembly. When attempting to raise a load greater than the jack’s capacity, the safety valve opens on each pump stroke and diverts any further oil back to the reservoir thus preventing the raising of the load.
(Previous models include product code/s; BSLAJ20)
Features
- Using CNC technology, the frame is constructed using superior-grade steel and built to premium TQ Pro standards for professional quality and durability
- Premium quality large diameter hydraulic steel cylinder with precision tolerances
- Piston-ram is treated and polished to minimise wear and extend service life
- High capability premium quality seal system efficiently protects internal hydraulics keeping it free from contaminants
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting premium finish
- Paint is oil, grease and dirt-resistant for easy cleanup
Thick Base Design
The thick base design is to provide the firmest footprint reducing flex. This substantially increases the life of the hydraulic ram under the toughest lifting and lowering circumstances.
Welded Reservoir
A welded reservoir instead of the screw base results in a substantial increase in durability. With the completely sealed hydraulic system, wear and tear and internal contamination is dramatically reduced.
Specifications
- Safe Working Capacity: 20,000kg
- Maximum Height: 330mm
- Minimum Height: 185mm
- Hydraulic Lift: 80mm
- Adjustable Height: 61mm
- Operating Air Pressure: 110-125psi
- Air Inlet Fitting: 1/4″
- Carton: 380 x 195 x 200mm
- Nett Weight: 16kg
- Gross Weight: 17kg
IMPORTANT: NEVER get beneath a vehicle that is only supported by a jack. ALWAYS chock the vehicle wheels and use support stands.
Intended Use
For professional specialist use on truck, agriculture, construction, mining, automotive and trailer applications whenever clearance is limited or very low to the ground.
(0 reviews) -
Transmission LiftersTQB BRANDS Clutch Jack – 130kg
The Borum Industrial 130kg Hydraulic Clutch Jack is perfect for earthmoving equipment and truck clutch and/or flywheel installation and removal. It features two fully adjustable splines, smooth, manually operated hydraulic lifting and lowering and four 360° swivel caster wheels for better load positioning. The ergonomic multi position rotating jacking handle makes overall maneuverability simple and efficient in a busy workshop.
Features
- Designed for lifting, lowering & installing/removing heavy vehicle clutch/flywheel assembles
- Frame is constructed of industrial-grade steel and built to exacting standards for quality and durability
- High quality hydraulic steel jacking cylinder results in low physical effort oil needed to lift load
- Industrial strength hydraulic system is protected from overload damage
- Filled with industrial grade 32 hydraulic fluid
- Rugged heavy industrial wheels and full swivel ball bearing castors
- User-friendly rotating pumping handle for maximum multi-directional operation
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting finish and to help prevent rust
- Paint is oil, grease and dirt-resistant for easy cleanup
- Two 10-tooth alignment splines included which conveniently stores on chassis
Specifications
- Safe Working Capacity: 130kg
- Minimum Height: 288mm
- Maximum Height: 980mm
- Chassis Dimensions: 1041 x 609mm
- 1 x 2″ Alignment Spline Included (10 Tooth)
- 1 x 1-3/4″ Alignment Spline Included (10 Tooth)
- Carton: 1070 x 710 x 220mm
- Gross Weight: 62kg
Intended Use
This clutch jack is designed to remove, install & transport (in the lowered position) 14″ and 15-1/2″ single and double disk clutches and/or flywheel assemblies on & off vehicles
(0 reviews) -
Wheel, Dollies & SuspensionTQB BRANDS Combi Portable Bead Breaker 5000kg
This Borum Industrial Hydraulic Bead Breaker delivers 5,000kg of force in seconds and is designed to work on most truck and tractor rims up to 26″. Ideal for use with all trucks, tractors, graders, harvester and skidder tyres, it suits all types of rims except 5-piece earthmover rims. It is expressly intended to be used as an aid in breaking the bead seal between a tyre and it’s one, two or three piece wheel rim for the purpose of reseating a bead seal, replacement of tyre or wheel and replacing tyre valves, tyre tubes etc. This Borum Industrial Hydraulic Bead Breaker can perform tyre work or tyre replacements without ever removing the wheel from the vehicle. This quality unit is excellent for field maintenance use on agricultural machines.
The bead breaker works directly on the bead of the tyre and will not damage the tyre if used correctly when used with the optional TradeQuip 2054T 10,000 psi air/hydraulic pump and the Eagle Pro EH-8206F Hydraulic Hose With Coupler.
Features
- Economical solution for agricultural wheels and 1, 2 and 3piece truck tyre rims
- Hydraulically clamps on wheel
- Durable steel construction
- Clamps to wheel rim & breaks bead simply with up to 5,000kg of force
- Requires 10,000psi air/hydraulic pump (sold separately)
- Most popular tool for breaking beads on most agricultural tyres
Specifications
- Safe Working Capacity: 5,000kg
- Rated Pressure: 10,000psi
- Maximum Rim Diameter: 660mm (26″)
- Maximum Rim Width: 125mm (5″)
- Ram Stroke: 90mm
- Pressure Connection: 3/8″ – 18NPTF
- Hydraulic Oil Capacity: 250ml
- Dimensions: 429x140x324mm
- Weight: 16kg
- Carton: 375x375x155mm
Intended Use
Designed to be used as an aid in breaking the bead seal between a tyre and it’s one, two or three piece wheel rim for the purpose of reseating a bead seal, replacement of tyre or wheel and replacing tyre valves, tyre tubes etc.
(0 reviews) -
Cranes & Lifting DevicesTQB BRANDS Engine Crane 3000kg
This Heavy Duty TradeQuip “Made for the Trade” Engine Crane has a long stroke lifting ram, a single action pump with a maximum load capacity of 3,000kg. Very simple to use manual hydraulic operation. The jib extends to the desired lifting capacity of 1000kg, 2000kg or 3000kg secured by a single locking pin. Mounted on heavy duty castor wheels for excellent manoeuvrability around the workshop. The lifting range is 0-2500mm so any large engine can be lifted clear out of the engine bay with little effort. With great stability of its wide legs, this crane can also be used to lift machines or other heavy items, making for an excellent piece of equipment for the workshop or warehouse.
Features- Industrial grade engine crane
- Heavy duty hydraulic pump
- Adjustable boom in four positions for lifting
- Robust steel fabricated legs with structural supports
- Large castor wheels for easy mobility
Specifications
- Safe Working Capacity: 3,000kg
- Folded Height: 1540mm
- Maximum Lifting Height @ 3000kg: 1745mm
- Maximum Lifting Height @ 1000kg: 2088mm
- Jib Length Fully Retracted @ 3000kg: 1100mm
- Jib Length Fully Extended @ 1000kg: 1730mm
- Overall Length Fully Extended: 2385mm
- Overall Length Fully Retracted: 1480mm
- Overall Width Fully Extended: 875mm
- Overall Width Fully Retracted: 785mm
- Distance Between Ram & Chain at 3T (Max hydraulic lift): 470mm
- Distance Between Ram & Chain at 2T (Max hydraulic lift): 650mm
- Distance Between Ram & Chain at 1.5T (Max hydraulic lift): 830mm
- Distance Between Ram & Chain at 1T (Max hydraulic lift): 1020mm
- Leg Height 190mm
- Nett Weight: 121.5kg
- Carton 1 of 3 : 1330 x 860 x 100mm (Weight: 29kg)
- Carton 2 of 3 : 1470 x 300 x 200mm (Weight: 82kg)
- Carton 3 of 3 : 700 x 180 x 150mm (Weight: 15kg)
Intended Use
For regular professional use, to raise and/or lower diesel engines and transmissions during service or repair work.
(0 reviews) -
Cranes & Lifting DevicesTQB BRANDS Engine Crane Foldable 1200kg
This Australian Standards AS1418.5 approved TradeQuip “Made for the Trade” hydraulic engine crane has a 8 tonne long stroke lifting ram and double acting pump with a maximum load capacity of 1,200kg. Very simple to use the ‘Quick-lift’ double acting hydraulic pump is equipped with automatic safety valve to control the lowering speed under load. This double action ‘Quicklift’ design… works by lifting the load on the UP and DOWN stroke of the ram handle.The jib extends to the desired lifting capacity of 250kg, 500kg, 750kg or 1200kg secured by a single locking pin. Mounted on 6 swivel castor wheels this engine crane has excellent manoeuvrability around the workshop. The lifting range is 0-2300mm so an engine can be lifted clear out of the engine bay with little effort. With great stability of its wide legs, this crane can also be used to lift machines or other heavy items, making for an excellent piece of equipment for the workshop or warehouse. It is also designed to quickly folds up when not in use to save space in the workshop.(Previous models include product code/s; 1000, 1000T, 1001)
Features- Ideal for automotive, light engineering and general workshops
- Adjustable boom in four positions for lifting
- Outrigger legs easily fold up for transport or storage
- Six swivel castor wheels allow easy mobility
- Double action 8,000kg long stroke hydraulic lifting ram
- Overload Protection
- Constructed of high-grade steel and built to exacting standards for quality and durability
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting finish and to help prevent rust
- Paint is oil, grease and dirt-resistant for easy cleanup
- Short lifting chain & hook with safety latch
- Easily exceeds Australian Standards AS1418.5 requirements
Specifications
- Safe Working Capacity: 1,200kg (AS1418.5 approved)
- Adjustable Boom: 250kg, 500kg, 750kg & 1200kg
- Lifting Ram Capacity: 8,000kg > Available as Spare Part: Product Code: 2008
- Stabiliser Arms Clearance: 195mm
- Dimensions: (Arms Ext): 2300(H) x 960(W) x 550(D)mm
- See pic for boom length, height and capacity
- Nett Weight: 85kg
- Carton 1 of 2 : 1440 x 300 x 160mm (Weight: 59kg)
- Carton 2 of 2 : 850 x 580 x 90mm (Weight: 32kg)
Intended Use
For regular professional use, to raise and/or lower passenger car engines and transmissions during service or repair work.
(0 reviews) - Ideal for automotive, light engineering and general workshops
-
Cranes & Lifting DevicesTQB BRANDS Engine Crane Load Leveller 680kg
The perfect accessory for our engine cranes, this TradeQuip “Made for the Trade” Engine Leveller reduces the hazards and hassles out of balancing heavy, awkward loads and helps protect engines, transmissions and vehicle damage. Perfect for removing and installing engines, it easily adjusts the angle of the engine simply by turning the swivel handle and is compatible with most good brands of engine cranes.The load leveller includes four 300mm chains with support brackets for increased load security and safety.
Features
- Easy to use, just crank to level
- Tilts forward and backward for easy motor mount alignment
- Heavy duty steel I-beam construction
- Balances engine/transmission for easier installation or removal
- Constructed of high-grade steel and built to exacting standards for quality and durability
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting finish and to help prevent rust
- Paint is oil, grease and dirt-resistant for easy cleanup
- Easily adapts to different engine cranes and improves the install/removal operation
- 4-point mounting system provides maximum control
- Worm drive shaft rotates with a built-in swivel handle for easy balancing
- 3 adjustable chain assembly holes for different engine sizes
Specifications
- Safe Working Capacity: 680kg
- Chain Length: 300mm
- Chain Anchor Positions: 3
- Engine Mount Positions: 4
- Working Range: 250mm, 275mm, 310mm
- Weight: 6kg
- Carton: 465 x 190 x 60mm
Intended Use
For regular professional use, to tilt engines and/or transmissions whilst raising and/or lowering passenger car engines and transmissions with an engine crane or hoist.
(0 reviews) -
Cranes & Lifting DevicesTQB BRANDS Engine Crane Ram 8000kg
This twin piston TradeQuip “Made for the Trade” 8,000kg Long Hydraulic Ram is the replacement hydraulic ram for use on TradeQuip 1001T hydraulic engine cranes. Mounts directly onto the engine crane and features a slow release function while providing a long 630–1135mm lift range. High quality large diameter twin cylinder hydraulic pump unit results in Quick Lift action, lower oil pressure needed to raise the load, which reduces wear and extends service life. 100% factory vertical load tested for reliability and safety. For vertical use only.
Replacement long hydraulic ram to suit TradeQuip 1001T Engine Crane.
Features
- Double action “Quick Lift” design for quick positioning without load
- Built in ‘Overload Protection’
- Constructed of high grade steel to exacting specifications for strength and durability
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting finish and to prevent rust
- Paint is oil, grease and dirt resistant
- Factory filled with high quality hydraulic jack oil, which offers better corrosion resistance and high/low temperature flexibility
- Includes lift handle for easy operation
Specifications
- Safe Working Capacity: 8,000kg
- Minimum Length: 630mm
- Maximum Length: 1135mm
- Ram Pin Hole: 16mm dia. 35mm Outside Ram
- Ram Diameter: 80mm
- Clevis Base Pin Hole: 16mm dia
- Clevis Base: 25mm Inside – 45mm Outside
- Base Width: 129mm
- Nett Weight: 10.5kg
- Carton: 700 x 170 x 150mm
- Gross Weight: 11.5kg
Intended Use
As a direct replacement for the hydraulic unit on a 1001T TradeQuip 1200kg Engine Crane only
(0 reviews) -
Engine Stands & SupportsTQB BRANDS Engine Stand 450kg
eQuipt “Designed to Deliver” 450kg Engine Stand has a 4-leg design featuring a rugged frame with a 4-hole mounting head that rotates 360°, making the unit ideal for 4 cylinder engines. When you’ve got an engine repair job that can’t be completed while the engine block is in the vehicle, this engine stand provides a sturdy support structure to secure the removed engine in mid-air, so you can access any part of it. Use an engine crane to remove the engine from the vehicle, then mount it to the faceplate on this engine stand. (Previous models include product code/s; 1006, RLES450, TQES450)
Features
- Rugged tubular steel frame with attractive durable finish
- 360 degree rotating head that locks in 8 positions
- Slotted mounting head for full adjustment
- Extra wide base for stability and safety
- Easy knockdown and quick assembly design for storing and transporting
- Large diameter wheels and castors for smooth manoeuvring
- Suitable for cast iron/alloy block engines up to 4 cylinder engines
Specifications
- Safe Working Capacity: 450kg
- Centre Height: 780mm
- Width @fixed wheels: 750mm
- Width @swivel castors: 400mm
- Dimensions: 760(L) x 750(W) x 860(H) mm
- Weight: 21kg
- Carton: 910 x 210 x 180mm
Intended Use
For safe handling and positioning of passenger car engines up to 4 cylinder during dismantling and re-assembly.
(0 reviews) -
Engine Stands & SupportsTQB BRANDS Engine Stand 680kg
This TradeQuip “Made for the Trade” 680kg Engine Stand delivers extra strength and accessibility, making it essential for busy garages. Easily adapts to accommodate a variety of engine sizes. “U” shaped base for added stability and support. Adjustable mounting brackets for attachment to engine block. 360° rotating mount head with multi-locking positions. 4 Heavy Duty steel swivel castors for easy manueverability. Legs can be removed for quick, convenient and easy storage. (Previous models include product code/s; 1191)
Features
- Constructed of high-grade steel and built to “Made for the Trade” standards for quality and durability
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting finish and prevent rust
- Paint is oil, grease and dirt-resistant for easy cleanup
- 360° swivelling and locking head allows easy rotation for obtaining the perfect angle position
- Long handle with rubber grips allows easy engine rotation
- Heavy-gauge tubular construction with industrial-grade steel bearing castors for easy maneuverability
- Mounting head has four adjustable arms with bolt holes to accommodate various load sizes
- Removable legs for convenient storage
Specifications
- Safe Working Capacity: 680kg
- Operating Height: 895mm
- Width: 800mm
- Length: 870mm
- Distance between legs: 670mm
- Lower steel tubing: 70x70mm
- Column tubing: 60x60mm
- Column base tubing: 70x76mm
- Leg tubing: 60x60mm
- Mounting head plate: 248x149mm
- Mounting head plate (with fingers): 360x245mm
- Nett Weight: 39kg
- Carton: 870 x 240 x 210mm
- Gross Weight: 41kg
Intended Use
For safe handling and positioning of most 4 and 6 cylinder passenger car engines during dismantling and re-assembly. WARNING: Engine dimensions must be within legs of Engine Stand.
(0 reviews) -
Engine Stands & SupportsTQB BRANDS Engine Stand Foldable 900kg
This TradeQuip “Made for the Trade” 900kg Engine Stand delivers extra strength and accessibility, making it essential for busy garages. Easily adapts to accommodate a variety of engine sizes. “H” shaped base for added stability and support. Adjustable mounting brackets for attachment to engine block. 360° rotating mount head with multi-locking positions. 5 steel swivel castors for easy maneuverability. Legs fold up for quick, convenient and easy storage. (Previous models include product code/s; 1192)
Features
- Constructed of high-grade steel and built to “Made for the Trade” standards for quality and durability
- Lead-free paint finish is applied after a thorough chemical wash to ensure a long-lasting finish and prevent rust
- Paint is oil, grease and dirt-resistant for easy cleanup
- 360° swivelling and locking head allows easy rotation for obtaining the perfect angle position
- Long handle with rubber grips allows easy engine rotation
- Heavy-gauge tubular construction with industrial-grade steel bearing castors for easy maneuverability
- Mounting head has four adjustable arms with bolt holes to accommodate various load sizes
- Foldable legs for convenient storage
Specifications
- Safe Working Capacity: 900kg
- Operating Height (A) : 800mm Floor to mounting plate centre
- Width(B) : 530mm
- Length (C): 1110mm
- ID between legs (D): 780mm
- OD between legs (E): 930mm
- Lower steel tubing: 60x60mm
- Column tubing: 70x70mm
- Nett Weight: 45kg
- Carton: 910 x 210 x 180mm
- Gross Weight: 43kg
Intended Use
For safe handling and positioning of most 6 and 8 cylinder passenger car engines during dismantling and re-assembly. WARNING: Engine dimensions must be within legs of Engine Stand.
(0 reviews) -
Engine Stands & SupportsTQB BRANDS Engine Support Bar 500kg
Constructed of heavy-duty powder coated steel for durability, the TradeQuip “Made for the Trade” Engine Support Bars are a must when working on under the bonnet repairs such as removing the transmission or transaxle. This 1019T Engine Support Bar comes with adjustable extension arms, neoprene support pads and adjustable height screw. Designed to support and accurately position engines during maintenance operations such as replacing engine/transmission mountings and certain body panels, the rubber padded support legs prevents slippage as well as protecting the paint.
Features- Adjustable to fit across most car bonnets
- Supports engine or transmission in place during repairs
- Rubber cushioned support legs prevent damage to paint
- Powder coat finish
- Adjustment screw for load levelling
- Supplied with a short length of chain
Specifications
- Safe Working Capacity: 500kg
- Minimum Extension: 1020mm
- Maximum Extension: 1600mm
- Carton: 1030 x 200 x 80mm
- Gross Weight: 18kg
Intended Use
Safely supports an engine in place during repairs such as replacing engine mounts or removing the transmission or transaxle without removing the engine.
(0 reviews) -
Engine Stands & SupportsTQB BRANDS Engine Support Bar 500kg
Constructed of high gloss enamel coated steel for durability, this TradeQuip 500kg capacity Engine Support Bar features dual hook assemblies for increased load balance when working on heavy engines or when removing the transmission or transaxle. This 1020T Engine Support Bar comes with adjustable extension arms, neoprene support pads and adjustable height screw. Designed to support and accurately position engines during maintenance operations such as replacing engine/transmission mountings and certain body panels, the rubber padded support legs prevents slippage as well as damage to paint.
Features- Dual hook assemblies for balanced support
- Adjustable to fit across most car bonnets
- Supports engine or transmission in place during repairs
- Rubber cushioned support legs prevent damage to paint
- High gloss enamel finish
- Adjustment screw for load levelling
- Supplied with a short length of chain
Specifications
- Safe Working Capacity: 500kg
- Minimum Extension: 1020mm
- Maximum Extension: 1430mm
- Nett Weight: 19kg
- Carton: 1530 x 120 x 120mm
- Gross Weight: 20kg
Intended Use
Safely supports an engine in place during repairs such as replacing engine mounts or removing the transmission or transaxle without removing the engine.
(0 reviews) -
Engine Stands & SupportsTQB BRANDS Engine Support Bar 500kg Dual Hook
Built to our TradeQuip “Made for the Trade” specifications, this transverse-mounted engine support bar has a two angle chain hook for safer and more stable chain support. This engine support bar features fully adjustable 4 point mounting system which will provide a very stable platform on any car. Weight rating is 500kg and includes eight rubber padded legs to prevent slipping and damage to cars finish. This tool features a dual hook design for holding engine or transmission in place. Finished in high gloss enamel for long life and durability. This design allows for improved stability, more flexibility and application to different vehicle types as well as added safety of 4 points of support and stability.
Perfectly suited for transverse and longitudinally-mounted engines alike.
Note: It is important that chains are hooked to both sides of hook, to ensure load is supported evenly.
Features- Cross bar feature for improved stability and more flexibility
- Dual hook assemblies for balanced support
- Adjustable to fit across most car bonnets
- Supports engine or transmission in place during repairs
- Extra long rubber cushioned support legs prevent damage to paint
- High gloss enamel finish
- Adjustment screws for load levelling
- Note: Chain not included
Specifications
- Safe Working Capacity: 500kg
- Minimum Extension: 1020mm
- Maximum Extension: 1630mm
- Nett Weight: 23kg
- Carton: 1730 x 180 x 80mm
- Gross Weight: 24kg
Intended Use
Safely supports an engine in place during repairs such as replacing engine mounts or removing the transmission or transaxle without removing the engine.
(0 reviews) -
Engine Stands & SupportsTQB BRANDS Foldable Engine Stand 680kg
This TradeQuip “Made for the Trade” 680kg Engine Stand is engineered from heavy-duty steel with a powder-coated finish, providing a durable and professional-grade solution for handling passenger and light commercial vehicle engines. Designed for maximum accessibility, the 360-degree rotating head and adjustable mounting arms allow for easy positioning during dismantling and re-assembly tasks across a wide range of engine blocks. The unit balances high-capacity strength with workshop efficiency, featuring smooth-rolling swivel casters for easy maneuverability and a quick-folding mechanism for space-saving storage when not in use.
Features
- Constructed with heavy-duty steel, providing long term durability with an industrial luster paint
- Mounting head features (4) adjustable arms and 360-degree rotation, allowing for easy access to any part of the engine
- Securely holds most foreign and domestic engine blocks
- Features a 680KG load capacity
- Equipped with 5 castors, including (2) 95mm fixed and (3) 76mm swivel castors, providing smooth and easy manoeuvrability.
- Quick folding mechanism allows for saving space when not in use during storage
- Powder coated finish for rust resistance and manufactured with precision for quality and performance
Specifications
- Safe working capacity: 680kg
- Maximum engine displacement: 5L
- No. of engine cylinders: 4-8
- Maximum engine length: 700mm
- 6 Locking positions
- 360º rotating head
- Dimensions (unfolded): 1000L x 800W x 1150H mm
- Dimensions (folded): 560L x 800W x 1150H mm
- Net weight: 32.4kg
- Gross weight: 33.5kg
Intended Use
For safe handling and positioning of passenger and light commercial vehicle engines during dismantling and re-assembly.
(0 reviews) -
Wheel, Dollies & SuspensionTQB BRANDS Giant OTR Bead Breaker 13000kg
The Borum Industrial Hydraulic Giant OTR Tyre/Earthmover Bead Breaker is designed to work on most multi-piece rims 25-51″ in diameter with pry bar pockets. Delivers up to 13,000kg of force with up to 10,000psi to break the toughest beads in seconds. Clamps to the wheel rim and utilises hydraulic pushrod to break the bead.The giant bead breaker works directly on the bead of the tyre and will not damage the tyre if used correctly.
The bead breaker works directly on the bead of the tyre and will not damage the tyre if used correctly when used with the optional TradeQuip 2054T 10,000 psi air/hydraulic pump and the Eagle Pro EH-8206F Hydraulic Hose With Coupler.
Features
- Economical solution for earthmover wheels 25” – 51” multi-piece rims with pry bar pockets
- Hydraulically clamps on wheel
- Design prevents lip kicking out
- Durable steel construction
- Lightweight, compact and portable design is safe and easy to use
- Hydraulic power breaks stubborn beads in seconds
Specifications
- Safe Working Capacity: 13,000kg
- Rated Pressure: 10,000psi
- Suitable for OTR Earthmover Rim Sizes: 25 – 51″ Diameter
- Pressure Connection: 3/8″ – 18NPTF
- Used on 5-piece rims 635 to 1,295 mm (25” – 51”) with pry bar / bead loosening pockets
- Ram Stroke: 105mm (4-1/4”) stroke ram
- Hydraulic Oil Capacity: 500ml
- Weight: 13kg
- Carton: 485x185x130mm
Intended Use
Designed to be used for separating tyres from rims on a large range of tyre and rim combinations on tractors, trucks, buses, earth movers or other similar vehicles. The inner-most surface of the tyre bead creates the air seal between the tyre and rim.
(0 reviews) -
Wheel, Dollies & SuspensionTQB BRANDS Heavy Duty Wheel Dolly Lifter 1200kg
This Borum Industrial Hydraulic 1200kg Heavy Duty Wheel Dolly Lifter is designed for the removal, installation and transportation of large truck, earthmoving, tractor and agricultural commercial tyre and wheel combinations. Hydraulically activated lift arms handle wheel assemblies from 1000mm up to 2000mm in wheel diameter. Four ball bearing mounted castor wheels provide positive stability and easy manoeuvrability. Quadruple bearing mounted lift rollers easily rotate vehicle rim & tyre for bolt pattern alignment while the integrated tyre clamp support arm keeps the wheel secured in place.
Features:
- Hydraulic system actuated to provide smooth, positive power for the removal and installation of large commercial wheel & tyre combinations
- Heavy duty steel frame adjusts laterally to allow precise positioning of commercial truck, earthmoving, agricultural & tractor tyres along with the wheel rollers for further control.
- Supports heavy commercial rims and tyres up to 1200kg
- Rolls easily on four quality steel bearing castors
- Includes heavy duty adjustable support arm to keep load secure
- Integrated locking pin secures the dolly to relieve hydraulic pressure under load
- Lead-free paint is applied to ensure a long-lasting finish and prevent corrosion
- Paint finish is oil, grease and dirt-resistant for easy cleanup
Specifications:
- Safe Working Capacity: 1200kg
- Min. Tyre Diameter: 1000mm
- Max. Tyre Diameter: 2000mm
- Lifting Range: 0 – 750mm
- Roller Length: 490mm
- Roller Diameter: 80mm
- Roller Table Area: 490 x 320mm
- Caster Wheel Diameter: 150mm
- Ground Clearance (Rollers Lowered): 90mm
- Jack Handle & Positioning Handle Length: 1000mm
- Minimum Footprint (Jack Handle Extended Out & Support Arm Vertical): 2000(L) x 1000(D) x 1340(H)mm
- Maximum Footprint (Jack Handle Extended Out & Support Arm Vertical): 2500(L) x 1000(D) x 2100(H)mm
- Crate Dimensions: 1340(L) x 1030(W) x 330(H)mm
- Nett Weight: 113kg
- Gross Weight: 143kg
Intended Use
Designed to facilitate the removal and installation of pneumatic tyres and wheel assemblies on earth movers, trucks, buses, agricultural machinery and trailers up to 1200kg & 2000mm diameter.
(0 reviews)