Shop
Showing 721–756 of 12034 results
-
Long Reach (Aircraft) HSSBORDO Long Reach (Aircraft) HSS Fractional
- Long Reach (Aircraft) Drill
- Long Reach Drills are suitable for all general purpose drilling where extra reach is required.
- Long Reach Drills are not designed to drill deep holes.
- Maximum hole depth must be less than the flute length (FL) of the drill.
- Deep hole drilling requires the use of a Bordo Long Series Drill, Bordo Extra Deep Hole Drill or Bordo Auger Bit depending on the material being drilled.
- 135° Split Point (crankshaft point)
- Split point is self centering reducing the need for end thrust.
- The 135° point provides superior performance when drilling harder steel materials.
- In most situations it will produce thicker chips minimising work hardening of the cavity.
- Faster penetration reduces abrasion and friction along the cutting edges.
- Black Finish Drills (also called blue finish) achieve their distinctive colour by steam tempering, a thermal process resulting in a porous tool coating.
- This surface helps to keep lubricant on the tool, particularly important on the cutting edges, thus reducing friction and cold welding.
- The result is increased tool life.
- Black finish tools are generally recommended for ferrous applications where the oxide layer aids chip flow and heat dissipation.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Long Series HSSBORDO Long Series Black HSS Fractional
- ANSI B94-11
- 118° chisel point with 30° helix.
- Chisel point is suitable for general purpose drilling.
- Black Finish Twist Drills (also called blue finish) achieve their distinctive colour by steam tempering, a thermal process resulting in a porous tool coating.
- This surface helps to keep lubricant on the tool, particularly important on the cutting edges, thus reducing friction and cold welding. The result is increased tool life.
- Black finish tools are generally recommended for ferrous applications where the oxide layer aids chip flow and heat dissipation.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Long Series HSS
BORDO Long Series Black HSS Metric
- ANSI B94-11
- 118° chisel point with 30° helix.
- Chisel point is suitable for general purpose drilling.
- Black Finish Twist Drills (also called blue finish) achieve their distinctive colour by steam tempering, a thermal process resulting in a porous tool coating.
- This surface helps to keep lubricant on the tool, particularly important on the cutting edges, thus reducing friction and cold welding. The result is increased tool life.
- Black finish tools are generally recommended for ferrous applications where the oxide layer aids chip flow and heat dissipation.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Long Series HSSBORDO Long Series Bright HSS Fractional
- ANSI B94-11
- 118° split point with 30° helix.
- Split point is self centering and reduces the need for end thrust. Friction at workpiece is reduced.
- 118° point angles are ideal for use in materials such as mild steel and cast iron.
- The 118° point creates easily controlled chips which are wide and thin.
- Bright Finish Twist Drills have no surface treatment and are supplied in the as-ground condition.
- These tools are suitable for general purpose use, particularly for non-ferrous applications.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Long Series HSS
BORDO Long Series Bright HSS Metric
- ANSI B94-11
- 118° split point with 30° helix.
- Split point is self centering and reduces the need for end thrust. Friction at workpiece is reduced.
- 118° point angles are ideal for use in materials such as mild steel and cast iron.
- The 118° point creates easily controlled chips which are wide and thin.
- Bright Finish Twist Drills have no surface treatment and are supplied in the as-ground condition.
- These tools are suitable for general purpose use, particularly for non-ferrous applications.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Insert Bit HoldersBORDO Magnetic Holders
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Annular Cutters & SetsBORDO MTS Adaptors for Annular Cutter
- Bordo hardened steel MTS Annular Cutter Adaptors allow the use of annular cutters in drill presses or lathes fitted with an MTS chuck.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BridgeBORDO MTS Bridge
- HSS Morse Taper Shank Tapered Spiral Flute Bridge Reamer
- Bridge reamers are used to create an aligned hole in a structural steel assembly. These reamers enlarge and align holes for rivets and bolts in structural steel members such as I-beams, angles, channels, and plates.
- The reamer is tapered for approximately half its FL allowing the reamer to enter out-of-line holes often encountered in structural work.
- All tools are constructed with left-hand spiral and right-hand cut.
- The left-hand spiral eliminates the tendency of the reamer to pull itself into the hole.
- In large structural assemblies, the holes are generally punched undersize and then reamed when in position.
- The idea is that the holes most likely will not line up within about 1/8″ when a fabricated 50 foot beam or column is finally put into place.
- Coolant or cutting tool lubricant should be utilitised when possible.
- Benefits include better finishes, superior tool life and the ability to increase speeds and feeds.
- Bridge reamers should be run at half the R.P.M. suggested for a corresponding twist drill size.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Morse Taper ShankBORDO MTS Extension Sockets
- Morse Taper Shank Extension Sockets are used to extend tool lengths and application distances.
- They are also designed to adapt morse taper shank tools to a larger, or smaller, morse taper holder.
- All Bordo MTS extension sockets are hardened and precision ground internally and externally.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
MTS MachineBORDO MTS Machine Fractional
- Bordo Morse Taper Shank Machine Reamers are made from premium quality HSS.
- 10° left hand spiral for effective swarf removal.
- Right hand cutting.
- H7 hole limit (tolerance).
- Machine reamers have a morse taper shank that enables a constant cutting force to be applied by the machine, and cutting starts immediately.
- Machine reamers have only a slight lead in to start.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
MTS Machine
BORDO MTS Machine Metric
- Bordo Morse Taper Shank Machine Reamers are made from premium quality HSS.
- 10° left hand spiral for effective swarf removal.
- Right hand cutting.
- H7 hole limit (tolerance).
- Machine reamers have a morse taper shank that enables a constant cutting force to be applied by the machine, and cutting starts immediately.
- Machine reamers have only a slight lead in to start.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Morse Taper ShankBORDO MTS Sleeves
- MTS sleeve – 1 internal, 2 external
- The Bordo range of Morse Taper Shank Sleeves are precision ground inside and out and are also fully through hardened.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Milling CuttersBORDO Multi Mills Metric Long – Threaded
- HSS-Co8 (Cobalt) end cutting, short threaded
- Multimills can cut in both axial and radial directions.
- They have exceptional chip evacuation and metal removal rates, while the flute design reduces vibration, even at high loads.
- The Multimill not only replaces two end mills to reduce tool-change and set-up times, but it also reduces the number of tools required in the machine set-up.
- Multimills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Three flutes deliver high metal removal rates as well as a high quality surface finish.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Milling CuttersBORDO Multi Mills Metric Short – Threaded
- HSS-Co8 (Cobalt) end cutting, long threaded
- Multimills can cut in both axial and radial directions.
- They have exceptional chip evacuation and metal removal rates, while the flute design reduces vibration, even at high loads.
- The Multimill not only replaces two end mills to reduce tool-change and set-up times, but it also reduces the number of tools required in the machine set-up.
- Multimills are used in milling applications such as profile milling, tracer milling, face milling, and plunging.
- Can be used in much harder materials than slot drills.
- Three flutes deliver high metal removal rates as well as a high quality surface finish.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Taps & DiesBORDO Multi-Size Tap & Drill Sets
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Multi-size Tap SetsBORDO Multi-Size Tap Sets
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BurrsBORDO Non-Ferrous Cut Ball 1/4″ Shank Diameter
- SC-1 Non-ferrous cut tungsten carbide burr.
- Non-Ferrous Cut Burrs are designed for rapid stock removal with minimum chip loading resulting in longer life and reduced clogging.
- Non-Ferrous Cut Burrs are for use on non-ferrous and non-metallic materials such as aluminium, brass, copper, bronze, coarse plastic, hard rubber, reinforced plastic and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BurrsBORDO Non-Ferrous Cut Ball Tree Radius Nose 1/4″ Shank Diameter
- SC-1 Non-ferrous cut tungsten carbide burr.
- Non-Ferrous Cut Burrs are designed for rapid stock removal with minimum chip loading resulting in longer life and reduced clogging.
- Non-Ferrous Cut Burrs are for use on non-ferrous and non-metallic materials such as aluminium, brass, copper, bronze, coarse plastic, hard rubber, reinforced plastic and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BurrsBORDO Non-Ferrous Cut Burr Set
- 3 Piece Non-Ferrous Burr Set
- Non-Ferrous Cut Burrs are designed for rapid stock removal with minimum chip loading resulting in longer life and reduced clogging.
- Non-Ferrous Cut Burrs are for use on non-ferrous and non-metallic materials such as aluminium, brass, copper, bronze, coarse plastic, hard rubber, reinforced plastic and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews) -
BurrsBORDO Non-Ferrous Cut Cylindrical 1/4″ Shank Diameter
- Non-Ferrous Cut Burrs are designed for rapid stock removal with minimum chip loading resulting in longer life and reduced clogging.
- Non-Ferrous Cut Burrs are for use on non-ferrous and non-metallic materials such as aluminium, brass, copper, bronze, coarse plastic, hard rubber, reinforced plastic and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BurrsBORDO Non-Ferrous Cut Cylindrical Ball Nose 1/4″ Shank Diameter
- SC-1 Non-ferrous cut tungsten carbide burr.
- Non-Ferrous Cut Burrs are designed for rapid stock removal with minimum chip loading resulting in longer life and reduced clogging.
- Non-Ferrous Cut Burrs are for use on non-ferrous and non-metallic materials such as aluminium, brass, copper, bronze, coarse plastic, hard rubber, reinforced plastic and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BurrsBORDO Non-Ferrous Cut Included Angle 1/4″ Shank Diameter
- SC-1 Non-ferrous cut tungsten carbide burr.
- Non-Ferrous Cut Burrs are designed for rapid stock removal with minimum chip loading resulting in longer life and reduced clogging.
- Non-Ferrous Cut Burrs are for use on non-ferrous and non-metallic materials such as aluminium, brass, copper, bronze, coarse plastic, hard rubber, reinforced plastic and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BurrsBORDO Non-Ferrous Cut Oval 1/4″ Shank Diameter
- SC-1 Non-ferrous cut tungsten carbide burr.
- Non-Ferrous Cut Burrs are designed for rapid stock removal with minimum chip loading resulting in longer life and reduced clogging.
- Non-Ferrous Cut Burrs are for use on non-ferrous and non-metallic materials such as aluminium, brass, copper, bronze, coarse plastic, hard rubber, reinforced plastic and fibreglass composite.
- Harder materials require slower running speeds.
- Smaller burrs require faster running speeds.
- Long shank burrs require slower speeds for safety reasons.
- Apply constant movement and light pressure when using the burr.
- Running below the optimum speed will cause chipping.
- Running above optimum speed will cause premature tooth wear.
- Allowing the burr to become too hot may cause the braze to soften, and cause the head to become detached from the shank.
- Using tools and collets which have become worn will cause chipping.
- Do not sink the burr for more than one third of its periphery.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Panel Drills HSSBORDO Panel Drills HSS Black Double Ended
- 135° Split Point (crankshaft point)
- Split point is self centering reducing the need for end thrust.
- The 135° point provides superior performance when drilling harder steel materials.
- In most situations it will produce thicker chips minimising work hardening of the cavity.
- Faster penetration reduces abrasion and friction along the cutting edges.
- Black Finish Drills (also called blue finish) achieve their distinctive colour by steam tempering, a thermal process resulting in a porous tool coating.
- This surface helps to keep lubricant on the tool, particularly important on the cutting edges, thus reducing friction and cold welding.
- The result is increased tool life.
- Black finish tools are generally recommended for ferrous applications where the oxide layer aids chip flow and heat dissipation.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Panel Drills HSSBORDO Panel Drills HSS Black Single Ended
- 135° Split Point (crankshaft point)
- Split point is self centering reducing the need for end thrust.
- The 135° point provides superior performance when drilling harder steel materials.
- In most situations it will produce thicker chips minimising work hardening of the cavity.
- Faster penetration reduces abrasion and friction along the cutting edges.
- Black Finish Drills (also called blue finish) achieve their distinctive colour by steam tempering, a thermal process resulting in a porous tool coating.
- This surface helps to keep lubricant on the tool, particularly important on the cutting edges, thus reducing friction and cold welding.
- The result is increased tool life.
- Black finish tools are generally recommended for ferrous applications where the oxide layer aids chip flow and heat dissipation.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Panel Drills HSSBORDO Panel Drills HSS Bright Double Ended
- 135° Split Point (crankshaft point)
- Split point is self centering reducing the need for end thrust.
- The 135° point provides superior performance when drilling harder steel materials.
- In most situations it will produce thicker chips minimising work hardening of the cavity.
- Faster penetration reduces abrasion and friction along the cutting edges.
- Bright Finish Drills have no surface treatment and are supplied in the as-ground condition.
- These tools are suitable for general purpose use, particularly for non-ferrous applications.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Panel Drills HSSBORDO Panel Drills HSS Bright Single Ended
- 135° Split Point (crankshaft point)
- Split point is self centering reducing the need for end thrust.
- The 135° point provides superior performance when drilling harder steel materials.
- In most situations it will produce thicker chips minimising work hardening of the cavity.
- Faster penetration reduces abrasion and friction along the cutting edges.
- Bright Finish Drills have no surface treatment and are supplied in the as-ground condition.
- These tools are suitable for general purpose use, particularly for non-ferrous applications.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
BrushwareBORDO Pipeline Brushes
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
PolishingBORDO Polishing Buffing Discs
- Medium hardness wool felt buffing discs are ideal for general purpose buffing, or polishing and cutting with any compound.
- They hold an edge well making them ideal for angles and corners.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
PolishingBORDO Polishing Compounds
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
PolishingBORDO Polishing Kit
- 3 Pce Calico Polishing Kit
- The ideal kit for a wide range of polishing needs.
- This set contains a mushroom head calico mop with hex spindle, a taper head calico mop with hex spindle, and green polishing compound.
- These items allow you to achieve a lustrous finish on: chrome, stainless steel, decorative copper, and brass.
(0 reviews) -
MopsBORDO Polishing Mops Calico Loose Leaf
- Polishing mops are for use on bench grinders fitted with a tapered spindle.
- Calico mops are used to create a lustrous, highly reflective polished finish, using either green, white or blue polishing compounds.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
PolishingBORDO Polishing Mops Calico With Shank
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
PolishingBORDO Polishing Mops Sisal
- Polishing mops are for use on bench grinders fitted with a tapered spindle.
- Sisal mops rough cut to remove scratches, belt marks, and drawing marks.
- When used with grey compound this mop has a high rate of surface removal.
- Fast and economical.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
PolishingBORDO Polishing Mops Stitched Rag
- Polishing mops are for use on bench grinders fitted with a tapered spindle.
- Stitched rag mops are used for fast cutting and a medium to high finish.
- Use brown or white compounds on soft metals such as aluminium, copper and brass.
- Use green compound for final cut and initial polish on stainless steel.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
PolishingBORDO Polishing Tapered Spindles
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page
