MILWAUKEE M12 FUEL™ 2 PIECE POWER PACK 2A
WHAT’S INCLUDED
M12 FUEL™ 13mm Hammer Drill/Driver (Tool Only)
M12 FUEL™ 1/4″ Hex Impact Driver (Tool Only)
M12™ REDLITHIUM™-ION 4.0Ah Battery
Related products
-
Power ToolsMILWAUKEE M18 FUEL™ D-Handle Jigsaw (Tool Only)
The M18 FUEL D-Handle Jigsaw combines power, blade speed and precision, to deliver quality cuts in a wide variety of materials and applications. Equipped with MILWAUKEE’s POWERSTATE Brushless Motor and REDLINK PLUS Intelligence, the M18 FUEL D-Handle Jigsaw provides high blade speed at 3500 strokes per minute, minimising chipping or bucking for clean controlled cuts. With the M18 REDLITHIUM-ION 5.0Ah battery, the saw is capable of cutting up to 35m of 19mm laminated particle board, delivering all-day productivity with less trips to the charger. The M18 FUEL D-Handle Jigsaw features a variable-speed two-finger trigger, toolless blade-change and bevel adjust, and an integrated LED light with on/off blower to maximise cutline visibility
(0 reviews) -
Power ToolsMILWAUKEE M18 FUEL™ 1/2″ Compact Impact Wrench with Pin Detent (Tool Only)
The M18 FUEL™ 1/2″ Compact Impact Wrench with Pin Detent delivers maximum access in tight spaces, up to 339 Nm of nut-busting torque, and maximum workspace visibility. This battery-powered impact wrench measures only 124.5 mm in length, with a POWERSTATE™ Brushless Motor to provide the power to remove stubborn fasteners, even in confined spaces. The MILWAUKEE® 1/2″ Compact Impact Wrench with Pin Detent has tri-LEDs that surround the anvil to deliver the user brighter light with fewer shadows. 4-Mode DRIVE CONTROL offers enhanced precision with a range of pre-set RPM and IPM levels, selectable from a single button on the tool. By selecting Mode 4, Auto Shut-Off Mode applies no more than 27 Nm of torque for hand-tight fastening applications to prevent overtightening. Mode 4 also features Bolt Removal Mode, where the tool delivers full torque output, then decreases RPMs once the bolt is loosened to prevent fastener drops. REDLINK™ PLUS Intelligence electronics make these controls possible while ensuring maximum performance, protecting the tool against overloads, over-heating, and over-discharge. The M18™ REDLITHIUM™-ION battery pack (not included) fits all M18™ tools, delivering more work per charge and more work over the life of the pack.
(0 reviews) -
Power ToolsITM Bench Drill Press
Quality casting, construction & componentry.
Emergency stop.
NVR safety switch.Each Unit Supplied With:.
Chuck safety guard.
Drill chuck & arbor.
Drill drift (on MT models)Drilling Capacity (mm): 16mm (5/8″)
Spindle Taper: #2MT
Chuck: 3-16mm B16
Motor Power: 375W 240V
Spindle Travel (mm): 85
Speed: 16 Speed 180-2770
Swing (mm): 325
Table Size / Base Size (mm): 290 / 420×250
Column Diameter (mm): 72
Height (mm): 980
N.W. / G.W. (kg): 43 / 45Drill press vice to suit: VDP102
Cross slide vice to suit: TM130-100(0 reviews) -
M18MILWAUKEE M18 FUEL™ 15GA FINISH NAILER (TOOL ONLY)
The M18 FUEL 15ga Finish Nailer delivers on the promise of peak productivity at your worksite, providing unmatched driving power, speed and efficiency – with practically no set up and minimal maintenance. Using the exceptional application speed, power and durability of our compact POWERSTATE Brushless Motor, plus our ready to fire cylinder design, this tool is capable of fully sinking 64mm nails into solid oak with zero ramp-up time. This 18-volt nailer operates from the revolutionary REDLITHIUM-ION Battery for unbeatable strength and run-time, eliminating the mess and cost of gas cartridges. It also includes REDLINK PLUS Intelligence, the most advanced electronic system on the market, to prevent damage to the nailer and battery from overloading and overheating. The M18 FUEL Nailer not only primes you for top performance; it also creates the experience of a pneumatic nailer that professional carpenters and remodelers expect, without the hassle of compressors and hoses.
(0 reviews)
