Cutting, Drilling & Abrasives
Showing 541–576 of 1275 results
-
Hole Saws & KitsDYMAXION Diamond Core Bits for Reinforced Concrete in Core Drilling Machines
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Hole Saws & KitsDYMAXION Diamond Core Bits Multi-Material inc. Concrete
- Suitable for cutting concrete, brick, compressed fibre cement sheet, granite and other masonry building materials.
- Utilising adaptor AUB100 these core drills can be used with core drilling machines.
- Diamond core drills and hole saws require the use of proper lubrication, correct drill speed and proper pressure.
- Drilling methods and techniques vary significantly depending upon the material being drilled.
- To achive optimum cutting performance and maximum core drill life use a slow to very slow drill speed, low drill pressure, and plenty of water for lubrication.
- Variable speed drills work best since the correct speed can be selected.
- Diamond core drills only drill out a portion of the resulting hole so they drill much faster than conventional blunt nose drills.
- The life of any type of diamond drill depends upon the hardness, abrasiveness and thickness of the material being drilled and the specific drilling techniques used.
- Using diamond core drills in hard materials is not difficult, however drilling the hole takes time.
- You should consider that they aren’t “drilling” a hole – they are “grinding” a hole.
- DO NOT USE HAMMER ACTION.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Diamond Sharpening ProductsDYMAXION Diamond Folding Sharpener
- Folding diamond sharpener.
- Medium Grit (400) diamond sharpening hone.
- Double sided.
- 20x100mm diamond pad.
- 20x225mm overall size when open.
(0 reviews) -
Hole Saws & KitsDYMAXION Diamond Hole Enlarger
- Use to enlarge an existing hole.
- Ideal for use in porcelain and stone – can also be used in most common building materials.
- Insert in drill and slowly guide the drill in an anti-clockwise direction around the hole to be enlarged.
- Use firm pressure against the surface to be removed.
- Can also be used to grind rebates and irregular shapes.
Diameter (mm): 35 Segment Height (mm): 25 Shank (mm): 10mm Hex Ideal For: Enlarging holes in porcelain and stone. (0 reviews) -
Cutting WheelsDYMAXION Diamond Internal Pipe Cutter
- Internal pipe cutters allow the user to cut PVC off square and clean below the finished surface / wall level.
- Useful for plumbing, tiling and electrical trades.
- Simplifies the process of squaring pipe ends prior to joining another length or fitting.
- Fast and efficient removal of grout between wall and floor tiles.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Diamond Sharpening ProductsDYMAXION Diamond Lap Stone
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Diamond Sharpening ProductsDYMAXION Diamond Needle File Set
- Set of 6 diamond needle files.
- Profiles are: square, round, half round, triangle, flat, and flat taper.
(0 reviews) -
Diamond Sharpening ProductsDYMAXION Diamond Pen Sharpener
- Diamond pen sharpener.
- Profiles are: 2/3 round, 1/3 flat, and 6mm round tapering to a point.
- Reversible.
- Includes embedded fish hook sharpener.
(0 reviews) -
Cutting WheelsDYMAXION Diamond Saw Blades Continuous Rim for glazed tiles
- Continuous rim blades have softer bonds for cutting hard materials such as tile, porcelain, granite, stone, glass, and other materials that can chip easily.
- These blades don’t have individual segments but instead have a solid, continuous rim or edge.
- Most continuous rim blades are designed for wet cutting applications, providing the smoothest, chip free cuts.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Grinding WheelsDYMAXION Diamond Saw Blades Diamond Cup grinding wheels
- Diamond Cup Wheel Turbo.
- For light grinding, shaping and finishing in concrete, stone and general masonry.
- Improved cooling for increased cup life.
- 100, 115, 125 & 180mm diameters.
- Ideal for removing formwork seams and imperfections in concrete and stone.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Cutting WheelsDYMAXION Diamond Saw Blades Electroplated general purpose
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Cutting WheelsDYMAXION Diamond Saw Blades Mesh Rim for ceramic tiles and stone
- Mesh Rim blades have softer bonds for cutting hard materials such as tile, porcelain, marble, and other materials that can chip easily.
- These blades have a thin 1.5mm kerf to minimise surface chipping and reduce cutting friction.
- Most continuous rim and mesh rim blades are designed for wet cutting applications, providing the smoothest, chip free cuts.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Cutting WheelsDYMAXION Diamond Saw Blades Segmented Rim for concrete, brick and pavers
- General purpose.
- Great for cutting a wide variety of non-abrasive materials.
- Can be used for either wet or dry cutting. Extended blade life will be experienced with wet cutting.
- Use when cutting cured concrete, reinforced concrete, clay bricks, hebel®, terracotta tiles, slate, granite, bluestone, fibreglass, reinforced plastics, wall chasing in brick & concrete.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Cutting WheelsDYMAXION Diamond Saw Blades Trenching and Chasing blades
- Rapid brick and mortar removal when trenching for electrical or plumbing applications.
- Can be used for either wet or dry cutting. Extended blade life will be experienced with wet cutting.
- Use when trenching or wall chasing in clay brick.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Cutting WheelsDYMAXION Diamond Saw Blades Turbo Rim for brick
- These Turbo Rim blades have bonds optimised for cutting clay brick and natural limestone.
- Turbo blades feature a continuous rim with an edge that is serrated.
- This serrated edge is designed to give the blade faster cutting speeds while maintaining a smooth cut, combining the best qualities from both segmented and continuous rim blades.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Cutting WheelsDYMAXION Diamond Saw Blades Turbo Rim for porcelain and granite
- Turbo blades typically have soft to medium bonds for a variety of general purpose to specific cutting applications.
- Turbo blades feature a continuous rim with an edge that is serrated.
- This serrated edge is designed to give the blade faster cutting speeds while maintaining a smooth cut, combining the best qualities from both segmented and continuous rim blades.
- Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
- The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
- Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
- If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
- If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
- Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
- The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
- The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Diamond Sharpening ProductsDYMAXION Diamond Sharpening Plate
- Diamond sharpening plate.
- Double sided. Medium Grit (400) one side and Super Fine Grit (1000) on reverse.
- Premium diamond sharpening plate fitted to a superior quality rubber bench holder.
- Large 205x65mm diamond pad.
(0 reviews) -
Hole Saws & KitsDYMAXION Diamond Turbo Core Bits for Brick – Dry Cutting 160mm long
- Suitable for cutting concrete, brick, compressed fibre cement sheet, granite and other masonry building materials.
- Utilising adaptor AUB100 these core drills can be used with core drilling machines.
- Diamond core drills and hole saws require the use of proper lubrication, correct drill speed and proper pressure.
- Drilling methods and techniques vary significantly depending upon the material being drilled.
- To achive optimum cutting performance and maximum core drill life use a slow to very slow drill speed, low drill pressure, and plenty of water for lubrication.
- Variable speed drills work best since the correct speed can be selected.
- Diamond core drills only drill out a portion of the resulting hole so they drill much faster than conventional blunt nose drills.
- The life of any type of diamond drill depends upon the hardness, abrasiveness and thickness of the material being drilled and the specific drilling techniques used.
- Using diamond core drills in hard materials is not difficult, however drilling the hole takes time.
- You should consider that they aren’t “drilling” a hole – they are “grinding” a hole.
- DO NOT USE HAMMER ACTION.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Hole Saws & KitsDYMAXION Drill Guides and Vacuum Suction Collectors
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Hole Saws & KitsDYMAXION Electroplated Diamond Hole Saws
- Diamond core drills and hole saws require the use of proper lubrication, correct drill speed and proper pressure.
- Drilling methods and techniques vary significantly depending upon the material being drilled.
- To achive optimum cutting performance and maximum core drill life use a slow to very slow drill speed, low drill pressure, and plenty of water for lubrication.
- Variable speed drills work best since the correct speed can be selected.
- Diamond core drills only drill out a portion of the resulting hole so they drill much faster than conventional blunt nose drills.
- Core drills can be used on most non-ferrous hard materials such as glass, ceramic, porcelain, fibreglass, slate, marble, granite and other natural and manufactured stone materials.
- The life of any type of diamond drill depends upon the hardness, abrasiveness and thickness of the material being drilled and the specific drilling techniques used.
- Using diamond core drills in hard materials is not difficult, however drilling the hole takes time.
- You should consider that they aren’t “drilling” a hole – they are “grinding” a hole.
- SPEEDS IN RPM: Fibreglass – 1200, Glass, Ceramic and China – 800, Limestone and Marble – 600, Ceramic Tile – 600, Porcelain – 500, Granite and Comp. Stone – 400.
- DO NOT USE HAMMER ACTION.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Grinding WheelsDYMAXION Grinding Disc Ferrous and Stainless Steels
- Suitable for grinding ferrous and stainless steels (inox).
- High grinding performance.
- High stock removal rates even at low pressure due to long tool life.
- Do not exceed maximum safe speed of 80m/s.
- Complies with DIN EN 12413 European standard and AS1788.1-1987 Australian standard.
- Grinding disc must be mounted correctly as per machine manufacturer’s specifications.
- Metal guards must be fitted and used on all machines.
- If grinding disc is chipped,cracked or damaged it must not be used, and needs to be replaced.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Diamond Sharpening ProductsDYMAXION Honing Guide
- Side clamping honing guide.
- For sharpening chisels and plane blades.
(0 reviews) -
Hole Saws & KitsDYMAXION Replacement Carbon Steel Cutters for all Adjustable Hole Saws 2 per pack
- Replacement high carbon steel blade set.
- Suitable for cutting all types of sheetmetal including brass and aluminium.
- Maximum sheetmetal thickness 1mm.
(0 reviews) -
Hole Saws & KitsDYMAXION Replacement dust shield for AHS220K Clear Acrylic
- Replacement dust shroud for AHS220K
- Impact resistant shroud with non-marking seal.
(0 reviews) -
Hole Saws & Kits
DYMAXION Replacement dust shield for AHS300K Clear Acrylic
- Replacement dust shroud for AHS300K
- Impact resistant shroud with non-marking seal.
(0 reviews) -
Hole Saws & KitsDYMAXION Replacement Tungsten Carbide Cutters for all Adjustable Hole Saws 2 per pack
- Replacement tungsten carbide blade set.
- Suitable for cutting timber, veneer, plywood, composite board, plasterboard, fibre cement sheet and acrylic sheet.
- Maximum cutting depth in timber 50mm.
(0 reviews) -
Hole Saws & KitsDYMAXION Replacement Tungsten Carbide Tip Pilot Drill
- Replacement TCT pilot drill.
(0 reviews) -
Hole Saws & KitsDYMAXION TCT Hole Saws for Metal Deep Cut
- TCT hole saws are ideal for repetition cutting in ferrous and non-ferrous plate and tube (including stainless steel), FRP and synthetic resin plates up to 5mm thick.
- Ideal for single hole, and through cutting, in round and square tube.
- Maximum material thickness 5mm.
- Extremely long service life.
- No need for messy cutting fluids, however use of a cutting lubricant will increase cutter life.
- Heavy duty plug ejector spring.
- Stop collar prevents cutter from over drilling.
- Maximum drilling depth of 20mm.
- Maintain a constant drilling angle (do not “rock” the cutter) to avoid tooth damage.
- Avoid restarting the same hole cut with pressure on the drill – tooth damage may result.
- Use slower drilling speed with constant drill pressure for optimum performance and tool life.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Hole Saws & Kits
DYMAXION TCT Hole Saws for Metal Standard Cut
- TCT hole saws are ideal for repetition cutting in steel plate and synthetic resin plates up to 5mm thick.
- Maximum material thickness 5mm.
- Extremely long service life.
- No need for messy cutting fluids, however use of a cutting lubricant will increase cutter life.
- Heavy duty plug ejector spring.
- Stop collar prevents cutter from over drilling.
- Maximum drilling depth of 5mm with ejector spring.
- Maximum drilling depth of 13mm without ejector spring.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Cutting WheelsDYMAXION Thin Cutting Disc Stainless Steel (INOX)
- Suitable for cutting stainless steel (inox).
- High cutting performance.
- Thin cut off discs reduce wastage.
- Fast cutting for extended battery life in cordless tools.
- Do not exceed maximum safe speed of 80m/s.
- Complies with DIN EN 12413 European standard and AS1788.1-1987 Australian standard.
- Cutting disc must be mounted correctly as per machine manufacturer’s specifications.
- Metal guards must be fitted and used on all machines.
- If cutting disc is chipped,cracked or damaged it must not be used, and needs to be replaced.
- Equal diameter flanges must be fitted. Flanges must be a minimum 1/3 diameter of cutting disc.
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Diamond Sharpening ProductsDYMAXION Tungsten Carbide Knife Sharpener
- Suction lever for quick and secure holding.
(0 reviews) -
Taps & DiesGOLIATH 3 Flute Tap Extractors
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Taps & DiesGOLIATH 4 Flute Tap Extractors
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Taps & DiesGOLIATH Adaptor
- Button die to die nut adaptor set – 3 piece
- Button die to die nut adaptor set.
- Contains adaptors to suit 1″, 1-1/2″ and 2″ circular button dies.
(0 reviews) -
Taps & DiesGOLIATH Bar Pattern Tap Wrenches Premium Range
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page -
Taps & DiesGOLIATH Bar Pattern Tap Wrenches Ratchet
(0 reviews)Add to Quote This product has multiple variants. The options may be chosen on the product page
