ITM 350mm Cermet Carbide Metal Cutting Blade

Related products

• 

  Circular Saw Blades

  BORDO TCT Circular Saw Blades Opticut

  • Opticut Precision Thin Kerf Blade for Timber – All Types
  • Optimum cutting thin kerf timber blades in 254mm and 305mm.
  • Thin kerf for fast, effortless cuts with reduced stock wastage.
  • High performance tooth geometries produce crisp, smooth cuts both with and across the grain, low feed resistance.
  • Tru-plate fully hardened and tempered steel body is precision balanced to run truer.
  • Ultra k-10 high density, high performance diamond ground carbide teeth for extreme durability and cutting life.

  (0 reviews)

  Add to Quote This product has multiple variants. The options may be chosen on the product page
• 

  Circular Saw Blades

  BORDO Diamond Saw Blades Hard Brick & Masonry

  • 350mm Segmented Diamond Hard Brick Blade
  • Hard brick and masonry.
  • 10mm segmented rim for fast cutting with enhanced blade/substrate interface cooling for long blade life.
  • Optimally designed for cutting cured concrete and stone.
  • Extreme concentration of diamond for fast, clean cutting and long blade life.
  • Can be used for either wet or dry cutting. Extended blade life will be experienced with wet cutting.
  • Use when cutting bluestone, hard clay brick, fire brick, cured concrete, concrete block, concrete brick, granite, marble, wall chasing in hard brick & concrete.
  • Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
  • The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
  • Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
  • If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
  • If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
  • Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
  • The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
  • The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.

  (0 reviews)

  Add to Quote
• 

  Circular Saw Blades

  BORDO Diamond Saw Blades General Purpose Segmented Rim

  • General purpose.
  • 7mm segmented rim produces clean, fast cuts wet and dry.
  • Great for cutting a wide variety of non-abrasive materials.
  • Extreme concentration of diamond for fast, clean cutting and long blade life.
  • Can be used for either wet or dry cutting. Extended blade life will be experienced with wet cutting.
  • Use when cutting cured concrete, reinforced concrete, clay bricks, hebel®, terracotta tiles, slate, granite, bluestone, fibreglass, reinforced plastics, wall chasing in brick & concrete.
  • Diamond blades do not cut, they actually grind through the material by exposing new diamond at the right moment just before the old diamond wears away.
  • The newly exposed diamonds again will wear, chip, or break out of the metal bond in the segment, while the metal bond gradually wears away to expose new diamond. This process is repeated over and over until there is no diamond remaining and the blade is worn out.
  • Ideally and to get the maximum life out of a diamond blade, the metal should wear away at just the right time to expose new diamond for optimum cutting performance.
  • If the metal wears away too quickly, the diamonds are exposed to soon and get torn out of the metal bond before they are fully worn. The result is a very short blade life.
  • If the metal wears away too slowly, the diamonds wear away before new diamond is exposed. This is often referred to as a ‘glazed blade’. Without exposed diamond the blade will not cut.
  • Abrasive materials like green concrete and asphalt will wear the metal bond very fast, so blades for these materials have a much harder metal bond to resist this abrasion.
  • The opposite occurs on a hard clay paver the clay paver is not abrasive enough to wear the metal bond fast enough to expose fresh diamond, therefore a different and much softer alloy is needed for cutting these types.
  • The single most important factor for the life of the blade is to match it to the job application and the type of equipment it is being used on.

  (0 reviews)

  Add to Quote This product has multiple variants. The options may be chosen on the product page
• 

  Circular Saw Blades

  BORDO Diamond Saw Blades Diamond Cup Wheels

  • Diamond Cup Wheel Single Row.
  • Economical cup wheel for flat grinding with fast material removal.
  • Ideal for removing imperfections in cured concrete.
  • 103, 125 & 180mm diameters.
  • Extreme diamond count.
  • Maximum material removal.
  • Dry grinding.

  (0 reviews)

  Add to Quote This product has multiple variants. The options may be chosen on the product page